If the maximum axial stress allowed in the wood piles is 51

Assignment Help Mechanical Engineering
Reference no: EM13621540

At a local marina, the dock is supported on wood piling in the manner . The top part AB, of one pile is above the normal waterline; the middle part, BC, is in direct contact with the water; and the part below C is underground. The original diameter of the pile is 300 mm, but action of the water and insects has reduced the diameter of the pile over the part BC. a) If the force that the deck exerts on the pile is P = 890 kN, what is the axial stress in AB? (neglect the weight of the pile itself) b) An inspector estimates that the diameter of the pile in segment BC has been eroded by 5%. What axial stress does the deck load of P = 890 kN produce in this damaged section of the pile? c) If the maximum axial stress allowed in the wood piles is 51 MPa (in compression), what is the maximum deck load that this damaged pile can support?

Reference no: EM13621540

Questions Cloud

A how long does it take for the proton to strike the top : two parallel plates have opposite charges and a distance between them measured to be 1.00 mm. the potential between the
How much current would the inductor mentioned in part a : a how much energy is stored in a 11.2 mh inductor carrying a 1.50a current?b how much current would the inductor
For a certain material failures were reported after 3000 : for a certain material failures were reported after 3000 hours at 650 c and 186 hours at 700 c when loaded at 250 mpa.
Gus games stock currently sells for 50 per share there are : 1. the three possible outcomes of an investemtn are listed below. all outcomes are equally likely. calculate the
If the maximum axial stress allowed in the wood piles is 51 : at a local marina the dock is supported on wood piling in the manner . the top part ab of one pile is above the normal
If the plates are separated by 050 cm what is the magnitude : a uniform electric field is established by connecting the plates of a parallel-plate capacitor to a 12.0 v battery.a if
Consider a customer service facility that is staffed with : consider a customer service facility that is staffed with 2 representatives. we assume that the amount of time a
Determine the change in the rate at which the following : pressurized water pin 10 bar tin 110 deg c enters the bottom of an l 10-m-long vertical tube of diameter d 100 mm
Consider the following data for a european option : consider the following data for a european option expiration 6 months stock price 80 exercise price 75 call option

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd