If the house size is approximately 30 by 10m and the wall

Assignment Help Mechanical Engineering
Reference no: EM13643224

A heat pump heating system supplies 5.8kW of thermal energy to the inside of a house. The external surfaces of the house have an average temperature of 2 degrees celcius on a cold day. The average thickness (x) and thermal conductivity (k) of the walls, ceilling and floors is 100mm and 0.04W/m.K respectively

1. If the house size is approximately 30 by 10m and the wall height is 2.6m what is the maximum temperature the inside of the house will heat up to once steady state is reached?

Equation:
J(heat) = Q/ At = k(T1-T2)/x

Where J(head) = heat flux, A = heat transfer area (m^2), Q = heat transfer (J), t = time, t1 = inside wall temperature, t2 = outside wall temperature

2. Suggest two ways the temperature in the house could be increased without buying a larger heater.

Reference no: EM13643224

Questions Cloud

An airplane has a mass of 34500 kg and takes off under the : an airplane has a mass of 34500 kg and takes off under the influence of a constant net force of 42500 n. what is the
The velocity of the water coming out is 075 ms calculate : a farmer in canterbury has a resource consent allowing him to use 100000l of water a day from the nearby river.
A positive charge of q1 is located 550 m to the left of a : a positive charge of q1 is located 5.50 m to the left of a negative charge -q2. the charges have different magnitudes.
Consider the compound sodium chloride in the solid form is : consider the compound sodium chloride. in the solid form is apperars white in color. however when heated it produces a
If the house size is approximately 30 by 10m and the wall : a heat pump heating system supplies 5.8kw of thermal energy to the inside of a house. the external surfaces of the
The dielectric constant of the material between the square : two capacitors have the same plate separation but one has square plates and the other has circular plates. the square
The work done by an external force to move a -840 mu c : the work done by an external force to move a -8.40 mu c charge from point a to point b is 1.30 times 10-3 j. if the
The density of aluminum is 270 gcm3 a piece of foil that : the density of aluminum is 2.70 gcm3. a piece of foil that is 10.00 cm on each side has a mass of 440. mg. how thick is
How much energy can this capacitor store without breaking : if the electric field inside a capacitor exceeds the dielectric strength of the dielectric between its plates the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd