If the dislocation is pi nned at two points 1 micron apart

Assignment Help Mechanical Engineering
Reference no: EM13612151

A sample of tungsten, W, contains an edge dislocation. W can be treated as elastically isotro pi c and the dislocation is on the specific slip plane (110), has a slip direction [-111] and a Burgers vector b=a/2[l11],

a) If the dislocation is pi nned at two points 1 micron apart so that it can be a Frank-Read source, what stress is needed to make it an active source?

b) If the dislocation was pi nned at two points 0.1 microns apart, what stress is needed to make it an active source?

c) Consider now the case where the dislocation is not pinned anywhere. However, another dislocation with the opposite Burgers vector lies on the same plane 1 micron from the first dislocation. Calculate the attraction between the two dislocation lines, (you will need to find this per unit length of dislocation line).

Reference no: EM13612151

Questions Cloud

Determine the fatigue strength at 5 x 105 cycles what is : the fatigue data for a brass alloy are given as followsstress amplitude mpa -----------------cycles to failure310
Financial statements of ansbro corporation follow : financial statements of ansbro corporation follow comparative balance sheet ending balance beginning balance assets
Todd holland from new york grows pumpkins he studied his : todd holland from new york grows pumpkins. he studied his past records carefully and concluded that the weights of his
After the rcs thruster is turned off find a the magnitude : a space vehicle is coasting at a constant velocity of 21.1 ms in the y direction relative to a space station. the pilot
If the dislocation is pi nned at two points 1 micron apart : a sample of tungsten w contains an edge dislocation. w can be treated as elastically isotro pi c and the dislocation is
A researcher conducted a study that examined the proportion : a researcher conducted a study that examined the proportion of high school students who cheated on tests at least twice
Excerpts from goodrow corporations most recent balance : excerpts from goodrow corporations most recent balance sheet and income statement appear below year 2 year 1 total
The ball leaves the club at a speed of 177 ms at an angle : a golfer hits a shot to a green that is elevated 3.00 m above the point where the ball is struck. the ball leaves the
In a survey of 1430 undergraduate students 1087 reported : in a survey of 1430 undergraduate students 1087 reported that they had one or more credit cards.a. provide a 90

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd