If the desired alcohol and sugar contents of the sherry

Assignment Help Mechanical Engineering
Reference no: EM13623407

Sherry wine is a blend of different wines. 200 kg of sherry was being produced by blending 3 different wines. Alcohol and sugar content of wines are given in the Table below. If the desired alcohol and sugar contents of the sherry blend are 16% w/v, and 3% w/v, calculate the amount of each wine needed to produce the sherry.

Wine        Alcohol, w/v %    Sugar % w/v

Wine A         14.6                    0.2

Wine B         16.7                    1.0

Wine C         17                       12

 

Reference no: EM13623407

Questions Cloud

A projectile is fired at an upward angle of 45deg from the : a projectile is fired at an upward angle of 45deg from the top of a 242 m cliff with a speed of 208 ms. what will be
The huang corporation needs to raise 66 million to finance : the huang corporation needs to raise 66 million to finance its expansion into new markets. the company will sell new
Consider a refrigerator with a coefficient of performance : consider a refrigerator with a coefficient of performance 6.1. suppose the temperature in the room outside the
Finally assuming that all paperwork was actually in order : find an article about all of the problems that occurred due to the failure of financial institutions to obtain and
If the desired alcohol and sugar contents of the sherry : sherry wine is a blend of different wines. 200 kg of sherry was being produced by blending 3 different wines. alcohol
Since the models cost about the same she was interested in : a computer laboratory manager was in charge of purchasing new battery packs for her lab of laptop computers. she
If the speed of a car is increased by 80 by what factor : if the speed of a car is increased by 80 by what factor will its minimum braking distance be increased assuming all
The environmental protection agency wanted to compare the : the environmental protection agency wanted to compare the proportion of plants in violation of air quality standards
What is meant by the term self-supporting growth rate how : what is meant by the term self-supporting growth rate? how is this rate related to the afn equation and how can the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If an air parcel at the surface was heated to 65 degree f

the measured lapse rate at a given location was 3.8 degree f per 1000 ft and the surface temperature was 60 degree f.

  Find the average power supplied by the engine

the 2 Mg car increases its speed uniformly from rest to 25 m/s in 30s up the inclined road. determine the maximum power that must be supplied by the engine, which operates with an efficiency of 0.8. also, find the average power supplied by the eng..

  The figure below shows the geometrical stress concentration

the figure below shows the geometrical stress concentration factor k for a flat bar loaded in uniaxial tension. the

  Acylindrical bar of steel e 209 gpa or 30 times106 psi v

a cylindrical bar of steel e 209 gpa or 30 times106 psi v 0.30 9.6 mm 0.3780 in. in diameter is to be deformed

  If the true mean is really 20 what sample size must be used

suppose we wish to test the hypotheses ho u15 h1 u does not 15 where we know that sigma2 9.0. if the true mean is

  The steel bolt and anchor assembly is used to reinforce the

the steel bolt and anchor assembly is used to reinforce the roof of a passageway in an underground coal mine. in

  Explain the first law of thermodynamics

Explain the first law of thermodynamics using the conversion of a fuel (gasoline or diesel) in an internal combustion engine. Provide sufficient details (sentences and illustration) to explain the first law.

  How many photons-water interactions occur in one second in

a beam of 2-mev photons with intensity 108 cm-2s-1 irradiates a small sample of water. a how many photons-water

  What is effect of increasing the cutting feed rate

What happens to the cutting and thrust force as tool rake angle and cutting speed are increased and what is the relation between the cutting and thrust forces to the depth of cut?

  Show the process on a pressure volume diagram locate the

a frictionless piston cylinder device contains 10kg of nitrogen initially at 200kpa and 27c. the nitrogen is now heated

  The chute is deployed is -0003 v2 speed v in feet per

the 230000 lb space shuttle orbiter touches down at about 220 mihr. at 200 mihr its drag parachute deploys. at 35 mihr

  The specific gravity of solids is 270 determine the

a soil sample has a total unit weight of 16.97 knm3 and a void ratio of 0.84. the specific gravity of solids is 2.70.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd