User Account

All Pages

If the design load on the prototype is 500 n what will be

Assignment Help Mechanical Engineering
Reference no: EM13631075

The drag on a 2-m. diameter satellite dish in an 80 km/hr wind is to be determined by a wind tunnel test using a geometrically similar dish with diameter 0.3 m. Use standard air for both the prototype and model.

a. What air speed should be used for the model test to ensure dynamic similarity?

b. If the design load on the prototype is 500 N, what will be the measured drag (N) on the model? What model design problem does this illustrate?

Reference no: EM13631075

Questions Cloud

The hose ends with a nozzle of diameter 240 cm a rubber : a village maintains a large tank with an open top containing water for emergencies. the water can drain from the tank
05 kg of water initially at 300 kpa 200oc is compressed in : 0.5 kg of water initially at 300 kpa 200oc is compressed in a piston-cylinder assembly to 1500 kpa 210oc. if heat
Assume ideal gases with a constant heat capacity of cp 293 : a vortex tube has an inlet air flow at 300 k and 5 bar. a vortex tube with 1 mole of input air outputs 0.8 moles 1 bar
A small leak occurs in one of the window seals in the : an airplane is cruising at an altitude of 10 km. the pressure outside the craft is 0.311 atm within the passenger
If the design load on the prototype is 500 n what will be : the drag on a 2-m. diameter satellite dish in an 80 kmhr wind is to be determined by a wind tunnel test using a
The piston rises to a new position doing 100 j of work on : a cylinder with a movable piston contains a gas. initially the gas temperature is 25 c. a two stage process happens. in
Tests on a geometrically-scaled model elbow will use water : a prototype 90 degree pipe elbow has ethyl alcohol at 20 degrees celsius flowing through it. the pressure drop through
Determine the power required in hp to heat the house using : a building for which the heat transfer rate through the walls and roof is 1350 btuh per degree temperature difference
Determine the maximum thermal efficiency for any power : ocean temperature energy conversion otec power plants generate power by utilizing the naturally occurring decrease with

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A closed system undergoes a process in which there is a

a closed system undergoes a process in which there is a heat transfer of 100 kj. if the initial specific internal

  The landsat-c earth resources satellite has a nearly

the landsat-c earth resources satellite has a nearly circular orbit with annbspeccentricity of 0.00132. at perigee the

  A state runs a lottery in which 6 numbers are randomly

a state runs a lottery in which 6 numbers are randomly selected from 40 without replacement. a player chooses 6 numbers

  The base surface of a cubical furnace 3-m x 3-m x 3-m is

the base surface of a cubical furnace 3-m x 3-m x 3-m is surrounded by black surfaces at a 1200 k. specified

  The boiler produces 40000 lbmshour of saturated steam and

a boiler produces saturated steam at 100psig pressure. the feedwater condensate returning to the boiler is saturated

  Saturated liquid water is heated at constant pressure in a

saturated liquid water is heated at constant pressure in a steady-flow device until it is a saturated vapor. calculate

  Calculate the rate at which heat is transferred tofrom the

steam enters a turbine at 8 mpa 450oc at a rate of 15 kgs and a velocity of 100 ms it leaves as saturated vapor at 100

  Derive equations for shear and moment

Design a wide flange, simply supported beam below so that the stress due to bending does not exceed that allowed by AISC for A36 steel and calculate the shear stress where the parts join as indicated. Maximum V = 10,000 lb.

  The stern winch takes in the towing cable at the rate of 2

the 580-ton tug is towing the 1200-ton coal barge at a steady speed of 6 knots. for a short period of time the stern

  A 03 kg bullet is fired into a 36 kg wooden block and

a 0.3 kg bullet is fired into a 3.6 kg wooden block and becomes embedded in it. knowing that the block and bullet move

  An electronics company has a contract to deliver

An electronics company has a contract to deliver

  Air at 3x10-4 kgs and 27o c enters a rectangular duct that

air at 3x10-4 kgs and 27o c enters a rectangular duct that is 1 m long and 4 mm by 16 mm on a side. a uniform heat flux

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd