If the compressor consumes 400 w of power and the cop the

Assignment Help Mechanical Engineering
Reference no: EM13614526

Refrigerant-134a enters the evaporator coils placed at the back of the freezer section of a household refrigerator at 100 kPa with a quality of 20 percent and leaves at 100 kPa and -26°C. If the compressor consumes 400 W of power and the COP the refrigerator is 2.2, determine (a) the mass flow rate of the refrigerant and (b) the rate of heat rejected to the kitchen air.

Reference no: EM13614526

Questions Cloud

A market research survey is available for 10000 using a : a market research survey is available for 10000. using a decision tree analysis it is found that the expected monetary
What is the mass of the spaceship and the acceleration due : a spaceship is heading toward planet x. while descending to the surface its rockets produce 25 kn of upward thrust and
A rational decision maker must choose between two : a rational decision maker must choose between two alternatives. alternative 1 has a higher emv than alternative 2 but
Rzio co purchases a machine for 12500 terms 210 n60 fob : rizio co. purchases a machine for 12500 terms 210 n60 fob shipping point. the seller prepaid the 360 freight charges
If the compressor consumes 400 w of power and the cop the : refrigerant-134a enters the evaporator coils placed at the back of the freezer section of a household refrigerator at
A football punter accelerates a football from rest to a : a football punter accelerates a football from rest to a speed of 11 ms during the time in which his toe is in contact
Transrail really wants this project and is considering a : transrail is bidding on a project that it figures will cost 400000 to perform. using a 25 markup it will charge 500000
How many times does the ball swing around each : my kids came up with a form of tether ball where they attached a ball to a string and let it swing around the role.
Iq scores of adults are normally distributed with a mean of : iq scores of adults are normally distributed with a mean of 100 and a standard deviation of 15. if one adult is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A water pump pumps out 2400kg of water pr min a if water

a water pump pumps out 2400kg of water pr min. a if water coming out with a velocity of 3ms what is power of the pump?

  If s is inclined 28 degrees from the vertical and the angle

vector r is the difference between vectors t and s. if s is inclined 28 degrees from the vertical and the angle between

  Determine the largest mass m

the pin c will support a force of 24 knmagnitude.Based on this criterion, you are asked to determine the largest mass m that the frame can safely support.the diameter of pulley at d is given as 0.2 m.find maximum mass m that can be supported by fr..

  We''re asked to determine the deflection of a beam location

We're asked to determine the deflection of a beam location for a 2000N load. However the force is directed up the corner NOT centroid.

  The steel bolt and anchor assembly is used to reinforce the

the steel bolt and anchor assembly is used to reinforce the roof of a passageway in an underground coal mine. in

  Determine the distance h that the sea water rises within

a heavy inverted cylinder of length l and radius r is initially held above the surface of the ocean density of sea

  The inner and outer surfaces of a 6-m x 7-m brick wall of

the inner and outer surfaces of a 6-m x 7-m brick wall of thickness 41 cm and thermal conductivity .69 wmc are

  Paint plant air house

Electricity might be used to run the fan to draw air through the system, and also to run a chiller - What is a typical COP for a commercial chiller?

  Is there an economic case for renewable energy

Is there an economic case for renewable energy? This issue was recently a "hot topic" in the news, and you are referred to the following newspaper article for a representation from the media.

  What is the percent span for the old and new set points

In order to increase production rate a reactor set point was increased from 160 psig to190 psig. The reactor pressure transmitter was recalibrated from 0-200 psig to 0-300 psig.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Determine how much force will be required to stretch them

a set of steel reinforcing rods is to be stretched axially in tension to create a tensile stress of 30ksi prior to

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd