If the collector can absorb 50 percent of the solar

Assignment Help Mechanical Engineering
Reference no: EM13644075

A solar thermal engine operating between 20 degrees celsius and 200 degrees celsius has efficiency equal to one-half of the Carnot efficiency. This engine needs to provide 5 kW power to drive a water pump. If the collector can absorb 50 percent of the solar insolation falling on the collector surface, determine the required area of the solar collector for a location where the averaged solar insolation is 800 W/m2.

Reference no: EM13644075

Questions Cloud

Two 50 g ice cubes are dropped into 200 g of water in a : two 50 g ice cubes are dropped into 200 g of water in a glass. if the water was initially at a temperature of 25oc and
The volume flow rate of the air returned to the workspace : air from a workspace enters an air conditioner unit at 30 degc dry bulb and 25 degc wet bulb. the air leaves the air
If a storm window is installed having the same thickness of : what is the rate of heat loss through a glass window 3.0 mm thick if the outside temperature is -20o c and the inside
The ambient conditions are p 100 kpa and t 25 degrees : a wind-turbine generator is designed to produce 3.5 x 106 kwhr per year with an annual plant factor of 0.40. the design
If the collector can absorb 50 percent of the solar : a solar thermal engine operating between 20 degrees celsius and 200 degrees celsius has efficiency equal to one-half of
The temperature of a household refrigerator is maintained : the temperature of a household refrigerator is maintained at 0c and the temperature of the room at 25c. the heat
Suppose that he uses 12 liter of tap water at 59o c and : a chef upon awaking one morning to find his stove out of order decides to boil the water for his wifes coffee by
Water flows through a horizomtal tube of length 25cm and : water flows through a horizomtal tube of length 25cm and internal diameter 1 mm under a constant head of the liquid
Using constant specific heats of air at room temperature : the compression ratio and cut of ratio of an air-standard diesel cycle are 16 and 2 respectively. at the beginning of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A 50kg lid is placed on a 20cm diameter container to form

a 50kg lid is placed on a 20cm diameter container to form a crude pressure vessel. the initial pressure is 1 atm and

  10 kg of water in a piston cylinder exists as a saturated

10 kg of water in a piston cylinder exists as a saturated mixture at 120 kpa with quality 40. the water is now heated

  The refrigerator steadily receives a power input of 015 kw

the refrigerator steadily receives a power input of 0.15 kw while rejecting energy by heat transfer to the surroundings

  If the discharge piping of the pump runs vertically upward

a pump raises the pressure of water from 100 kpa to 900 kpa and raises the velocity from 1 ms to 20 ms. the flow rate

  Determine the hertz contact stresses for a 50 n coupling

a 2-2-2 kinematic coupling uses 19-mm silicon nitride balls and tungsten carbide vees. determine the hertz contact

  What is the velocity of the fluid at the measurement point

a pitot-static tube measures the stagnation and static pressure of air at 8.5 and 1.5 of h2o respectively. what is the

  The tubes have center to center distance of 15 inches in

an in-line tube bank is constructed of 1 inch diameter tubes with 15 rows transverse to the flow 7 rows in the floe

  The whole system is now heated until the volume of chamber

in this piston-cylinder device d1 20 cm-diameter d2 10 cm-diameter and the initial volume of chamber 2 is 0.1 m3.

  Explain derive an expression for the bounding energy

Derive an expression for the bounding energy Eo in terms of the equilibrium interionic separation ro and the constants D, and p using the following procedure

  The outlet area and velocity are 001 ft2 and 10 fts

a steady-flow compressor is used to compress helium from 15 psia and 70of at the inlet to 200 psia and 600of at the

  A hydraulic cylinder is diameter

A hydraulic cylinder is 100mm diameter and is fed by a pipe 15mm in diameter. If the piston in the cylinder moves forward at a rate of 0.2ms^1

  Ten kilograms of ice at 260 k is dumped into 20 kg of

ten kilograms of ice at 260 k is dumped into 20 kg of liquid water initially at 300 k in an insulated container. the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd