User Account

All Pages

If the actual flow rate consumed by the motor is 0005 m3s

Assignment Help Mechanical Engineering
Reference no: EM13639701

A hydraulic motor has a displacement of 130 cm3 and operates with a pressure of 105 bars and a speed of 2000 rpm. If the actual flow rate consumed by the motor is 0.005 m3/s and the actual torque delivered by the motor is 200 N/m, find

a. volumetric efficiency
b. Mechanical Efficiency
c. Total Efficiency
d. kW power delivered by the motor.

Reference no: EM13639701

Questions Cloud

What is the final velocity just before hitting the ground : a plane is flying at 120 ms and drops cargo to people 500 meters below. 1where do the people need to stand in relation
The probability that no defects are found in a batch : a particular consumer product is being assembled on production lines ab and c and packaged in batches of 10. each day
A researcher suspects that the pressure gauge on a 499-l : a researcher suspects that the pressure gauge on a 49.9-l gas cylinder containing nitric oxide is broken. an empty gas
At high temperatures phosgene cocl2 decomposes to give : at high temperatures phosgene cocl2 decomposes to give carbon monoxide co and cl2. in a typical experiment 0.631 g of
If the actual flow rate consumed by the motor is 0005 m3s : a hydraulic motor has a displacement of 130 cm3 and operates with a pressure of 105 bars and a speed of 2000 rpm. if
Once leaving the cylinder a regulator reduces the pressure : once leaving the cylinder a regulator reduces the pressure to 15.0 psig and a valve allows 1.000 mls of ethylene at
Blood cholesterol levels are generally expressed as : blood cholesterol levels are generally expressed as milligrams of cholesterol per deciliter of blood. what is the
A 6 nominal pipe size schedule 40 steel pipe has a : a 6 nominal pipe size schedule 40 steel pipe has a chamfered entrance and 300 ft. long. the velocity is 20 ft per sec.
A simple random sample of 10 software widgets are chosen : a simple random sample of 10 software widgets are chosen for installation. if 10 of this type of software widgets have

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the fraction of the throttle mass flow that

consider a regenerative rankine cycle with a 600c and 4-mpa throttle a 5-kpa condenser and an open feedwater heater at

  Pressure in the radiator drops to 100kpa in 30 minutes by

a steam radiator in a well-insulated room 4m times 4m times 5m contains superheated vapor at 200kpa 200c. it has a

  Determine the approximate rate of heat loss from the sphere

a hollow spherical iron container whose outer diameter is 20 cm and the thickness is 0.4 cm is filled with ice water at

  Consider a house whose walls are 4 m high and 12 m long two

consider a house whose walls are 4 m high and 12 m long. two of the walls of the house have no windows while each of

  A projectile is launched horizontally with an initial

a projectile is launched horizontally with an initial velocity of 25.8 ms and lands on a slope that inclined at 28

  What power is required to drive each screw when the gate is

two identical 3 in. major-diamter power screws single-threaded with modified square threads are used to raise and lower

  Assume that the tests indicated that a tensile stress of

an internal crack has been detected by means of x-rays in the shell of a large cylindrical pressure vessel. the

  A bar of high strength aluminum alloy is 150 mm long and

a bar of high strength aluminum alloy is 150 mm long and has a circular cross section of diameter 40mm. it is subjected

  Steam at 10 psia with a quality of 090 enters an adiabatic

steam at 10 psia with a quality of 0.90 enters an adiabatic steady-flow compressor at a rate of 50 lbms. the steam

  Is it better for the air in the wind tunnel to be cold or

consider the common situation in which a researcher is trying to match the reynolds number of a large prototype vehicle

  Draw the shear and bending moment diagrams for the beam

draw the shear and bending moment diagrams for the beam and loading shown and determine the maximum normal stress due

  A 100ft cable is made using a 12-gauge 01055in steel wire

a 100ft cable is made using a 12-gauge 0.1055in steel wire and three strands of 10gauge .1019in copper wire. find the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd