If kinetic and potential energy changes of the air from

Assignment Help Mechanical Engineering
Reference no: EM13637431

Air is compressed at steady state from 1 bar, 300 K, to 6 bar with a mass flow rate of 4 kg/s. Each unit of mass passing from inlet to exit undergoes a process described by pv^1.27= constant. Heat transfer occurs to the cooling water circulating in a water jacket enclosing the compressor at a rate of 46.95 kJ per kg of air flowing. If kinetic and potential energy changes of the air from inlet to exit are negligible, calculate the compressor power.

Reference no: EM13637431

Questions Cloud

Would it be a possible to use a normal domestic : would it be a possible to use a normal domestic refrigerator as a heat source for a small hot tub or whirlpool? if so
A student designs an ammeter a device that measures : a student designs an ammeter a device that measures electricalcurrent that is based on the electrolysis of water into
A survey found that americans generate an average of 198 : a survey found that americans generate an average of 19.8 pounds of glass garbage each year. assume the standard
Resistors are assigned a power rating if the power rating : resistors are assigned a power rating. if the power rating is exceeded significantly the resistor will overheat and
If kinetic and potential energy changes of the air from : air is compressed at steady state from 1 bar 300 k to 6 bar with a mass flow rate of 4 kgs. each unit of mass passing
Objects a and b are both positively charged both have a : objects a and b are both positively charged. both have a mass of 200 g but a has twice the charge of b. when a and b
A 774 g ice cube floats in the artic sea the temperature : a 77.4 g ice cube floats in the artic sea. the temperature and pressure of the system and surroundings are at 1 atm and
Calculate the magnitude e of the net electric field at the : a point charge q1-4.00nc is at the point x 0.600 meters y 0.800 meters and a second point charge q26.00nc is at the
Calculate the percentage of azomethane that it will : the initial rates listed in the table were determined for thethermal decomposition of azomethane ch3nnch3ch3nnch3 g

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A hydraulic jack has a load piston diameter of 150 mm and a

a hydraulic jack has a load piston diameter of 150 mm and a plunger diameter of 25 mm. ignoring losses what force will

  Determine the number of automobiles with premair catalyst

determine the number of automobiles with premair catalyst treated radiators needed to reduce the ozone concentration in

  An acher shoots an arrow vertically upward if the arrow

an acher shoots an arrow vertically upward. if the arrow ascends to a maximum height of 100 feeta find the value of

  What is the percent span for the old and new set points

In order to increase production rate a reactor set point was increased from 160 psig to190 psig. The reactor pressure transmitter was recalibrated from 0-200 psig to 0-300 psig.

  After this force is applied the length of the cylinder

a cylinder of an aluminum alloy with a radius of 2.00 cm and a length of 11.00000cm is subjected to a force of 41.0kn.

  In a rigid chamber 30 lbm of helium is heated from 60

in a rigid chamber 30 lbm of helium is heated from 60 degrees farenhight and 30 psig to 90 degrees farenhight. if

  All four sides of the plate are maintained at 20 degree c

a 50-cm by 50-cm plate of pure nickel generates 3.9 mwnr of energy uniformly within the plate. all four sides of the

  What is effect of increasing the cutting feed rate

What happens to the cutting and thrust force as tool rake angle and cutting speed are increased and what is the relation between the cutting and thrust forces to the depth of cut?

  The bead is supported by a cable ac determine the force

a bead a weighting 2lb slides on a quarter-circular frictionless bar bc with radius. the bead is supported by a cable

  If methane burns in oxygen at an equivalence ratio phi15

an inventor has devised an atmospheric-pressure process to manufacture methanol. the inventor claims he has developed a

  Effect of material hardness

On a single graph, plot "Hardness" as the ordinate versus "Aging Time" as the abscissa for each aging temperature - Discuss the effect of aging time and temperature on the effect of material hardness.

  In moles of an ideal gas a and 1-nmoles of an ideal gas b

in moles of an ideal gas a and 1-nmoles of an ideal gas b each at 1 atm are mixed at total constant pressure. what

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd