If each unit mass of air passing from inlet to exit

Assignment Help Mechanical Engineering
Reference no: EM13611427

Air enters a compressor operating at steady state with a pressure of 14.7lbf/in^2 and a volumetric flow rate of 8 ft^3/s. the air velocity in the exit pipe is 225 ft/s and the exit pressure is 150 lbf/in^2. If each unit mass of air passing from inlet to exit undergoes a process described pv^1.3=constant, determine the diameter of the exit pipe, in inches.

Reference no: EM13611427

Questions Cloud

The nitrogen is compressed to frac12 of the initial volume : two kg of nitrogen at 40degc and 200 kpa are contained in a frictionless piston-cylinder device. the nitrogen is
A nuclear reactor continuously generates 150 mw of : a nuclear reactor continuously generates 150 mw of powerthrough the fissioning of uranium. suppose that each
To charges and are located at the origin and at 045 0 : two charges and are located at the origin and at 0.45 0 respectively.where on the x-axis must a third charge of
A nuclear reactor continuously generates 150 mw of : a nuclear reactor continuously generates 150 mw of powerthrough the fissioning of uranium. suppose that each
If each unit mass of air passing from inlet to exit : air enters a compressor operating at steady state with a pressure of 14.7lbfin2 and a volumetric flow rate of 8 ft3s.
What will be the equilibrium temperature when a 245 g block : what will be the equilibrium temperature when a 245 g block of lead at 300oc is placed in 150-g aluminum container
Determine how much time is required for the ball to reach a : a 4-lb ball b is traveling around in a circle of radius r1 3 ft with a speed vb1 6 fts. if the attached cord is
Explain and demonstrate the use of bonds and other debt : 1. the nature of the business in brief all three companies ebay - worlds largest online marketplace where anyone can
An irregular conductor carries a surface charge density of : an irregular conductor carries a surface charge density of -6.75 cm2 at and in the vicinity of a point p on the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Evaluate the coefficient of performance assume cv for the

using the compressibility chart determine the volume in m3 occupied by 20 kg of hydrogen h2 at 11.55 atm and -364 degf.

  Determine the turbine efficiency and the combined

it is proposed to generate electrical power by installing a hydraulic turbine-generator at a site 70 m below the free

  Determine the velocity of point b, c, d, and e

Crank AB of the linkage shown rotates clockwise at 300 rpm. Using graphical method, determine the velocity of point B, C, D, and E.

  Calculate the final pressure and volume of the system

The process and volume relation is given p=(8-4v)bar for a non flow process ,where V is in cubic meter.If 130kJ of work is supplied to the system,calculate the final pressure and volume of the system.Take the initial volume as 0.5 cubic meter.

  What is the concentration in kilograms of silicon per cubic

the concentration of silicon in an iron-silicon alloy is 0.55 wt. what is the concentration in kilograms of silicon per

  Develop equations which may be solved to give the final

develop equations which may be solved to give the final temperature of the gas remaining in a tank nbspafter the tank

  Determine the following a the gas pressure lbfin2 when the

a gas is contained in a vertical piston-cylinder arrangement. the 50-lbm piston initially rests on the bottom stops.

  What tension can be applied to the conductor if the

an electrical conductor is composed of a steel core 116 inch in diameter surrounded by a 364 inch thick shell of

  The temperature of the inner surface of this pipe is 50 c

hot water flows through a pvc k.092 wmk pipe whose inner diameter is 2 cm and outer is 2.5 cm. the temperature of the

  A 250 mm bar of 15mm x 30 mm rectangular cross-section

a 250 mm bar of 15mm x 30 mm rectangular cross-section consists of two aluminum layers which are 5 mm thick each brazed

  Enough heat is added until the tank contains only saturated

a 1 m3 rigid tank contains a two-phase mixture of saturated liquid water and saturated water vapor at atmospheric

  The polynomial method is to be used to solve the equation

The polynomial method is to be used to solve the equation. For the graphs, Mathcad or similar program is necessary to graph the solution.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd