If each unit mass of air passing from inlet to exit

Assignment Help Mechanical Engineering
Reference no: EM13605935

Air enters a compressor operating at steady state with a pressure of 1 bar, a temperature of 20°C, and a volumetric flow rate of 0.25 m3/s. The air velocity in the exit pipe is 210 m/s and the exit pressure is 1 MPa. If each unit mass of air passing from inlet to exit undergoes a process described by pv1.34 = constant, determine the exit temperature, in °C and the diameter of the exit pipe.

Reference no: EM13605935

Questions Cloud

The earths crust is broken up into a series of more-or-less : the earths crust is broken up into a series of more-or-less rigid plates that slide around due to motion of material in
Which of the following systems provides for a separate : which of the following systems provides for a separate record of the cost of each particular quantity of product that
Given the cost and activity observations for smithson : given the cost and activity observations for smithson companys utilities use the high-low method to calculate smithsons
A school district receives a grant from the federal : a school district receives a grant from the federal government to support programs directed at lsquolsquospecial needs
If each unit mass of air passing from inlet to exit : air enters a compressor operating at steady state with a pressure of 1 bar a temperature of 20degc and a volumetric
Discuss why it is necessary for accountants to assume that : discuss why it is necessary for accountants to assume that an economic entity will remain a going concern. if an entity
At this rate how many minutes would it take such a scramjet : on march 27 2004 the united states successfully tested the hypersonic x-43a scramjet which flew at mach 7 seven times
The direct material in your answer is only multiply 1440 : the direct material in your answer is only multiply 14.40 time 2400 which is the number all the custom seat. however
The boyd school district began a recent fiscal year with : the boyd school district began a recent fiscal year with 3000 of supplies in stock. during its fiscal year it engaged

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the maximum axial compressive force

A short 60-mm-diameter circular bar is made of a material for which the maximum safe compressive stress is 80 MPa and the maximum safe shearing stress is 30 MPa. Determine the maximum axial compressive force that can be safely applied.

  Determine the reaction at end a and b

determine (a) the reaction at end A and B , (b) the minimum required cofficient of static friction at end A

  Neglect the size of the limb

, determine the speed of the boy at the instant = 4 . Neglect the size of the limb. When = 0, = 8 so that and are coincident, i. e., the rope is 16 long.

  Destructive tests and non destructive

Whats are examples of destructive tests and non destructive

  Although thenbspbuoy normally floats on the surface at

a spherical buoy has a diameter of 1.5 mnbspweighs 8.50 kn and is anchored to the sea floornbspwith a cable as is shown

  Consider a hollow steel sphere of inside radius r110 cm and

consider a hollow steel sphere of inside radius r110 cm and outside radius of r220 cm. the thermal conductivity of the

  The a-36 steel axle is made from tubes ab and cd and a

the a-36 steel axle is made from tubes ab and cd and a solid section bc. it is supported on smooth bearings that allow

  Plastics and other polymeric materials are expensive with

plastics and other polymeric materials are expensive with respect to steel and are usually more costly than aluminum

  A satellite is in earth orbit with an altitude at perigee

a satellite is in earth orbit with an altitude at perigee of 555.0 km and an altitude at apogee of 1200.0 km. a. what

  What is the maximum pressure this unit can withstand

a power unit has a power rating of 30 kw and supplies flow at a rate of 60 lpm, what is the maximum pressure this unit can withstand?

  Make a form tool for lathe for making a convex groove

Make a form tool for lathe for making a convex groove of 3 mm radius. tool material will be tungsten carbide. Know the dimensions of tool.

  Calculate the force and pressure acting across the pelvis

calculate the force and pressure acting across the pelvis and at the feet of a 150 lbm person. model the body using

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd