If a strain of -0087 is measured by a strain gage what

Assignment Help Mechanical Engineering
Reference no: EM13626238

A bar of aluminum is subjected to a tensile load of 15000 lbs. If the bar is 0.35 inches in diameter and 20 inches long determine the following...E modulus is 10*10^6 psi

A. average stress

B. average strain

BB. axial strain

C. If the axial strain in the bar were to be 0.18, how long would the bar be?

D. For an axial compressive strain of -0.07, what will the lateral strain be?

E. If a strain of -0.087 is measured by a strain gage, what stress must the Aluminum be experiencing?

F. If the bar is pourus nd you have a strain of 0.04 at a stress of 60,000psi , what is the effective modulus of the material?

Reference no: EM13626238

Questions Cloud

Air at 3x10-4 kgs and 27o c enters a rectangular duct that : air at 3x10-4 kgs and 27o c enters a rectangular duct that is 1 m long and 4 mm by 16 mm on a side. a uniform heat flux
The mass and volume of an american penny made after 1982 : a racquetball with a diameter of 5.6 cm and a mass of 42 g is cut in half to make a boat for american pennies made
If a coal-burning electrical generating plant burns 2 tons : if a coal-burning electrical generating plant burns 2 tons of coal to generate 6000 kwh of electricity calculate the
The end of a robtoic arm extends along the path of the : the end of a robtoic arm extends along the path of the limacon r 1.5 cos thetam. at the instant that theta pi4 the
If a strain of -0087 is measured by a strain gage what : a bar of aluminum is subjected to a tensile load of 15000 lbs. if the bar is 0.35 inches in diameter and 20 inches long
Refrigerant 134a enters a compressor with a mass flow rate : refrigerant 134a enters a compressor with a mass flow rate of 5 kgs and negligible velocity. the refrigerant enters the
Light is incident of the surface of metallic sodium whose : light is incident of the surface of metallic sodium whose work function is 2.3 ev. the maximum speed of the
Suppose a survey participant is randomly selected and you : drake marketing and promotions has randomly surveyed 200 men who watch professional sports. the men were separated
Crate slides down the section of the spiral ramp such that : crate slides down the section of the spiral ramp such that r .5zft and z 100 - .1t2ft where t is in seconds. if the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd