If a light bulb bought from a particular store has a 18

Assignment Help Mechanical Engineering
Reference no: EM13631277

If a light bulb bought from a particular store has a 1.8% probability of being defective when it leaves the store, calculate the probabilities below.

1. What is the probability that eight of them purchased at the same time contain exactly one defective blub?

2. What is the probability that eight of them purchased at the same time contain at least one defective bulb?

Reference no: EM13631277

Questions Cloud

Find the power of the starlight the earth intercepts one : consider a bright star in our night sky. assume its distance from earth is 20.9 light-years ly and its power output is
A standard deviation of 47 mph what is the probability that : if the maximum wind speed generated in a thunderstorm is described by a normal distribution with a mean of 39.5 mph and
What is the magnitude of the force of the car on the truck : a 800kg car pushes a 1900kg truck that has a dead battery. when the driver steps on the accelerator the drive wheels
Liquid octane c8h18 is burned in the constant pressure : liquid octane c8h18 is burned in the constant pressure adiabatic combustor of an aircraft engine with 40 percent excess
If a light bulb bought from a particular store has a 18 : if a light bulb bought from a particular store has a 1.8 probability of being defective when it leaves the store
A weight of 300 n is suspended from a spring that has a : a weight of 30.0 n is suspended from a spring that has a force constant of 190 nm. the system is undamped and is
What is refraction how and why does it occur why does : what is refraction? how and why does it occur? why does light change its speed as it passes from one medium to
A 1500 lb crate is pulled along the around at a constant : a 1500 lb crate is pulled along the around at a constant speed for a distance of 25ft using a cable that makes an andle
Find the velocity of the stream issuing out of the nozzle : two streams of air one at 1 bar 27degree and velocity of 30 ms and the other at 5 bar 227 degree and 50 ms velocity mix

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A copper-nickel alloy of composition 60 wt ni-40 wt cu is

a copper-nickel alloy of composition 60 wt ni-40 wt cu is slowly heated from a temperature of 1000degc 2370degf. what

  One of the problems of wind tunnel testing at airspeeds

one of the problems of wind tunnel testing at airspeeds near sonic speed is the large effect on the flow conditions of

  During the charging process pressure in the cylinder

an insulated piston-cylinder device initially contains 10kg saturated liquid water at 200kpa. now water steam at 0.5mpa

  A valve in a cylinder has a cross sectional area of 11 cm2

a valve in a cylinder has a cross sectional area of 11 cm2 with a pressure of 735 kpa inside the cylinder and 99 kpa

  A long spring with a k50 lbin is cut into three equal

a long spring with a k50 lbin is cut into three equal parts. the resulting springs are connected to a 386 lb block as

  How many bq becquerels of 90sr are present b how many bq of

a 6.2 mg sample of 90sr half-life 29.12 y is in secular equilibrium with its daughter 90y half-life 64.0 h. a how many

  A car is moving with a constant speed of 40 kmh along a

a car is moving with a constant speed of 40 kmh along a straight road which heads towards a large vertical wall and

  For a specific design the desired radial load was converted

1. for a specific design the desired radial load was converted to the equivalent c10 load of 14.2 kn. if a 25 mm bore

  Calculate compression ratio cr pressure and temperature at

a six cylinder diesel engine with a 4.5 inch. bore for each cylinder and 5.0 inches stroke works on a theoretical

  Determine the time t required for the disk to acquire its

the initially stationary uniform disk of mass m1 and radius b is allowed to drop onto the moving belt from a very small

  Determine the maximum possible volume flow rate for this

a 5 kw pump operating at steady state receives liquid water at 100 kpa 15 c and delivers it to a point 6 m above the

  A 600 mw coal-fired power plant has an overall thermal

a 600 mw coal-fired power plant has an overall thermal efficiency of 38. it is burning coal that has a heating value of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd