Identify each corner by a suitable description on the sketch

Assignment Help Civil Engineering
Reference no: EM13545541

1.Show by means of a sketch , the cap inscription for a corner common to Sections 33 and 34 in Township 8 North, Range 12 West, and Sections 3 and 4 in Township 7 North, Range 12 West.

2.Make a sketch indicating the incorrect and correct positions of such an original section corner and also the positions of the adjacent corners used in relocating that corner. Identify each corner by a suitable description on the sketch .

3.When using the rectangular surveying system, under what circumstances is there an exception to the general law that an identified original section corner controls the positions of the boundary lines meeting at or passing through the corner ?

Reference no: EM13545541

Questions Cloud

Identify the errors in the accountants adjusting entries : The accountant for Rooster Laundry prepared the following unadjusted and adjusted trial balances. Assume that all balances in the unadjusted trial balance and the amounts of the adjustments are correct. Identify the errors in the accountant's adju..
Determine the minimum height of the hump to produce critical : A rectangular concrete channel 10 m wide has a bed slope of 1 m/km and surface roughness equivalent to a Manning n of 0.02. It is proposed to use a hump on the channel bed for the purpose of flow measurement. If the maximum discharge is 150 m3/s:
Accounting system and method of revenue recognition : Simona Amanar Industries has two operating divisions-Gina Construction Division and Chorkina Securities Division. Each division maintains its own accounting system and method of revenue recognition.
Estimate the force on the chimney and the bending moment : Estimate the force on the chimney and the bending moment at the bottom of the chimney. You may assume that the effect of the wind on the first 1 m height of the chimney has a negligible effect on the force and the moment.
Identify each corner by a suitable description on the sketch : When using the rectangular surveying system, under what circumstances is there an exception to the general law that an identified original section corner controls the positions of the boundary lines meeting at or passing through the corner ?
Design a rectangular channel contraction from width b1 : Design a rectangular channel contraction from width b1 (upstream) to width b2 (downstream). Assume uniform flow approaches the contraction (i.e. normal depth approaching the channel contraction).
Determine the force exerted by the belt on the package : A series of small packages, each with a mass of 0.5 kg, are discharged from a conveyor belt. Knowing that the coefficient of static friction between each package and the conveyor belt is 0.4, determine (a) the force exerted by the belt on the package
When the axial load p is applied show that the axial : The steel shaft of diameter D is cemented to the thin rubber sleeve of thick-ness t and length L. The outer surface of the sleeve is bonded to a rigid support.
What are the velocity and flow rate in the prototype : A dam spillway is to be tested using kinematic similitude (Froude scaling) with a 1:20-scale model. The model flow has an average velocity of 0.7 m/s and a flow rate of 0.06 m3/s.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Engineering ethics and ethical issue

what is the engineering ethics course where to write about any engineering ethical case and discuss the ethical issue?

  Engineering ethics and concept and cases

what is the engineering ethics case related to civil engineering with reference and discuss all the engineering ethics issues which covered the "Engineering etics concepte and cases?

  Transportation and management

In the construction management, there is a lot of procurement route that are necessary and suitable for the construction industry.

  Supporting Investment Promotion: ERNST & YOUNG

Ernst & young is currently providing support to various sectors. In this regards it was felt that if this report is able to document good practices currently being adopted or planned in ceramic sector.

  Personalized Cancer Therapy-A step forward

Cancer is the uncontrolled growth of abnormal cells in the body resulting in tumours that can be benign or malignant (cancerous cells). A proper treatment is necessary to fight with this serious disease.

  Discuss the different environmental companies

Discuss the different agencies, institutes, centers, different environmental companies that are active in UAE.

  Develop a simple urban constructed wetland design

Develop a simple urban constructed wetland design.

  Evaluate company performance in relation to GRI standards

Evaluate company performance in relation to GRI standards and comment on Stigler's theory.

  Water system design

Determine the corresponding error in the computed discharge

  Hydraulic behaviour in open channel

Describe how test flumes and associated equipment are used to assess and confirm hydraulic behaviour in open channel

  Write a paper on steel sustainability

Write a paper on steel sustainability.

  Writing case study about bridge collapse

Writing case study about bridge collapse

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd