Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Assignment on Timber and Masonry Deterioration
Q1:
The timber bridge shown in Photograph 1 and Photograph 2 below shows clear signs of deterioration in different elements of the bridge. Your task is to identify three different forms of deterioration that had already taken place or that may take place in the bridge elements.
Q2.
The brick façade in the multi-storey residential tower in Photos (3-6) below was inspected and a number of photographs taken for cracking in the bricks of the façade. The building was built in 1960s and consists of reinforced concrete floors and columns as the main load bearing structural frame and is clad in some areas with wire cut clay brick façade. The cracks in the brick façade were mainly concentrated along a line joining the concrete balustrades of the balconies as shown in the photographs. Your task is to analyse the photographs and come up with an explanation for the cracking, bulging and distortion of the brick unit. Highlight the main characteristic of clay bricks that is responsible for the symptoms for seen in the photographs.
Attachment:- assignment.rar
Verified Expert
The paper is based on knowledge about timber and masonry. There are two accretions in the paper. First one is about Timber bridge deterioration. Solution to the question is provided for 500 word for this part. In next section, an explanation for the cracking, bulging and distortion of the brick unit is provided. The solution also highlight the main characteristic of clay bricks that is responsible for the symptoms. This part is prepared for 500 words. The complete length of paper is 1000 words.
I want 4 copies of the same assignment done in a different way.i need to submit by tomorrow afternoon.please let me know if u can send the 4 copies before due time Assignment on Timber and Masonry Deterioration
The water pressure acting on a masonry dam varies as shown. If the dam is 20 ft wide, determine the resultant force of the water pressure acting on the dam.
A rear-wheel-drive 3000-lb drag race car has a 200-inch wheelbase and a center of gravity 20 inches above the pavement and 140 inches behind the front axle
An underground gasoline storage tank has leaked benzene into an unconfined aquifer over a period of several months. The aquifer characteristics are: Ambient temperature=8 oC Hydraulic conductivity = 123 ft/day Hydraulic gradient = 0.00091 ft/ft
Water flows in a 100 m long pipe at 3 m/s. If the water temperature is 20 degrees C, determine the minimum valve-closure time to avoid creating water hammer pressures. What is the maximum water-hammer pressure that can occur
On a shovel/truck operation the production of the shovel is 293 BCY/h and a job efficiency of 0.75. The trucks used have a capacity of 12 BCY and have a cycle time of 45 min.(excluding loading).
What horizontal acceleration α0 should be given to the plate so that the absolute acceleration of the slider will be vertically down? What is the value of the corresponding force R exerted on the slider by the slot?
Assume that gasoline is burned with 99% efficiency in a car engine, with 1% remaining unburned in the exhaust gases as VOCs. If the engine exhausts 16 kg of gases (MW = 30) for each kg of gasoline (MW = 100)
The stream hts a stationary splitter, such that half of the flow is diverted upward at 45o. and the other half is directed downward, and both streams have a final speed of 18ft/s.
The 500- bed Lotta Hart Hospital has a small activated sludge plant to treat its wastewater. The average daily hospital discharge is 1200 L/day per bed
A power plant for a polar expedition uses ammonia and the boiler exit is 80?C, 1000 kPa, and the condenser operates at -15?C. A single open FWH operates at 400 kPa with an exit state of saturated liquid. Find the mass fraction extracted in the tur..
determine the force in member AC, FH, and FG and indicate if the member is in tension or compression. List all zero force members.
Disadvantage of buying a plant
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd