Hydrogen and nitrogen in different proportions

Assignment Help Mechanical Engineering
Reference no: EM13881638

Gas streams containing hydrogen and nitrogen in different proportions are produced on request by blending gases from two feed tanks: Tank A (hydrogen mole fraction = xA) and Tank B (hydrogen mole fraction = xB). The requests specify the desired hydrogen mole fraction, xp, and mass flow rate of the product stream, mp(kg/h).

(a) Suppose the feed tank compositions are xA = 0.10 mol H2/mol and xB = 0.50 mol H2/mol, and the desired blend-stream mole fraction and mass flow rate are xp = 0.20 mol H2/mol and mp = 100 kg/h. Draw and label a flowchart and calculate the required molar flow rates of the feed mixtures, nA (k mol/h) and nB (k mol/h).

(b) Derive a series of formulas for nA and nB in terms of xA, xB, xp, and mp. Test them using the values in part (a).

(c) Write a spreadsheet that has column headings xA, xB, xp, mp, nA, and nB. The spreadsheet should calculate entries in the last two columns corresponding to data in the first four. In the first six data rows of the spreadsheet, do the calculations for XA = 0.10, x = 0.50, and xp = 0.10, 0.20, 0.30, 0.40, 0.50, and 0.60, all for mp = 100 kg/h. Then in the next six rows repeat the calculations for the same values of XA, XB, and Xp for mp = 250 kg/h. Explain any of your results that appear strange or impossible.

(d) Enter the formulas of part (b) into an equation-solving program. Run the program to determine A and B for the 12 sets of input variable values given in part (c) and explain any physically impossible results.

Reference no: EM13881638

Questions Cloud

Which robot is the better economic option : (a) Which robot is the better economic option? (b) Using the spreadsheet Goal Seek tool, determine the first cost of the robot not selected in ( a ) so that it will be the economic selection.
Mortgage lending product of bank muscat : Make a report of 12000 words on Mortgage lending product of Bank Muscat. Distinguish it from the conventional mortgage lending product and analyse its position in the market and Evaluate the current portfolio of Baituna home loans product of Bank Mus..
Pioneer report the change : 1.At the beginning of 2013, Pioneer Products' ownership interest in the common stock of LLB Co. increased to the point that it became appropriate to begin using the equity method of accounting for the investment.
Why do robert symptoms increase in the first two days : Why do Robert's symptoms increase in the first two days? Why is he given glucocorticoids? Based on the fact that Robert was not given tPA, what is the most likely cause of the CVA
Hydrogen and nitrogen in different proportions : Gas streams containing hydrogen and nitrogen in different proportions are produced on request by blending gases from two feed tanks: Tank A (hydrogen mole fraction = xA) and Tank B (hydrogen mole fraction = xB). The requests specify the desired hy..
How does a marketer balance the short-term gains : How does a marketer balance the short-term gains that sales promotion can deliver against the possible negative long-term consequences such promotions might have for brands? Use appropriate examples.
The appropriate reporting category for this investment : December 31, 2013, and December 31, 2014, the market value of IBM stock is $58 and $61 per share, respectively.
Maintain a constant media schedule : It is usually unnecessary or not feasible to maintain a constant media schedule all year. What are the two other alternatives and what key characteristics of these two alternatives would be taken into account?
Calculation of the percent excess air : If it is possible to do so without additional information, calculate the percent excess air supplied to the furnace: if more information is needed, state what it is and outline the calculation of the percent excess air.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If the oxygen undergoes adiabatic expansion through the

oxygen at 710 kpa and 365 celcius enters a staedy flow nozzle with a low velocity and leaves at 90 kpa. if the oxygen

  The measurement is to be performed with an uncertainty of

a pneumatic displacement gage is to be used to measure displacement between 0.1 and 0.2 mm. the output of the device is

  Express fc and fab as functions of x

Consider the jib crane shown in the given image, where it is supported by a pin at C and rod AB. The maximum tension allowed in the rod is 60 kN and the maximum rated force in the pin C is 80 kN. The load has a mass of 2000 Kg with its center of m..

  Find out the coefficients m and b of the function you

below is measured voltage v at different time stimes 0 0.5 1 1.5 2 2.5

  Find the initial pressure and mass of the system

Water in the pictured piston cylinder assembly has an initial quality of 10%. The piston cylinder is 20 cm in width and the piston is initially 40 cm high. Heat is added until the temperature of the steam reaches 500°C. While heat is being added the ..

  Moore machine and a mealy machine

Initially, you are required to design both a Moore machine and a Mealy machine and discuss the advantages/disadvantages of each. For these initial circuit designs, use D flip-flops as the memory elements, then build and test both circuits on Yenka..

  Determine the pressure on the bottom surface of the fluid

a 6.5m tall tank has a rectangular cross?section and is filled with water to a depth of 3.5m. assuming the pressure on

  The welding department has idle capacity of 600 minutes per

a single unit of product a requires 2.4 minutes of punch press time and 5.0 minutes of assembly time. the profit for

  Calculate the plant net power in megawatts

Consider a power plant operating on an ideal Rankine cycle without feed water heating. Steam enters the turbine saturated at 1000F at the rate of 5 x10 lbm/H. The turbine exhausts to a surface condenser at 1 psia. The condenser has an overall heat tr..

  Determine what kind of drive is best and to select suitable

determine what kind of drive is best and to select suitable components .the driven equipment requires 60hp and should

  The plate is subjected to an axial force of 75 kn the

the a-36 steel plate has a thickness of 12 mm and other dimensions. r30mm p60mm ab200mm bc800mm cd200 width120mm. the

  Consider an ideal vapor-compression refrigeration cycle the

consider an ideal vapor-compression refrigeration cycle. the refrigerator employs refrigerant 134a as the working fluid

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd