Human body-what is the oxygen pumping rate in g per minute

Assignment Help Mechanical Engineering
Reference no: EM13708085

Consider human body. A 70 kg human has about 5 L of blood and it is pumped by heart at about 5.2 LPM (liter of liquid blood per minute). At any given time, the lungs transfer oxygen from alveoli to blood capillaries and the oxygen concentration in blood capillaries is given as 200 mL of O2 per L of blood (5 % of this oxygen is in dissolved state i.e O2 molecules sandwiched between H2O molecules while 95% is tied to Haemoglobin Hb i.e O2 molecules chemically bound to Hb. The concentration of Hb is 160 g/L and M=68800 g/mole. You do not this information for problem). Note that the mL of O2 is gas volume equivalent at CST (called Chemists standard temperature of 0 C and pressure of 101 kPa) while L of blood represents liquid blood of density1.06 g/cm3.

a) Based on your knowledge of ideal gas law, express the concentration of for O2 in g of O2 per g of blood.

b) How much oxygen (in g) is contained in 5 L of blood?

c) What is the oxygen pumping rate in g per minute?

d) However 75 % of this oxygen is returned back to alveoli which you breathe out. Thus only 25 % oxygen is used for burning glucose (i.e. Glucose delivered to blood from the food you ate three times a day) called metabolism in biology. How much oxygen in g/min is used for metabolism?

e) If 14500 J of energy is released per g of O2 used for metabolism, what is the energy released rate of human in Watts.

 

{Almost 20 % of this energy is used by your brain, a super-super-.. Einstein living with everyone on globe which controls all our functions; so even a few min of absence oxygen flow to brain may leads to death. Just like automobile engine you breathe in 360 Liters per hour and instead of gasoline you burn glucose and/or fat 24 hrs per day 7 days per week, … until human engines stop}

Reference no: EM13708085

Questions Cloud

Find expressions for the induced transverse stresses : A cube of linear elastic material is subjected to a vertical compressive stress sigma1 in the 1-direction, but it is now constrained ( e = 0) in both the 2- and 3- directions. Find expressions for the induced transverse stresses, sigma2 and sigma3 in..
Estimate the molar volume : The Molar Volume of Al2O3 at 25 Degrees Celsius and 1 atm is 25.715 cc/mol. Its coefficient of thermal expansion is 26 x10^-6 K^-1 and the coefficient of compressibility is 8.0 x10^-7 atm^-1. Estimate the molar volume of Al2O3 at 400 degrees Celsius ..
Calculate the average linear velocity : An aquifer has a hydraulic conductivity of 12 ft/day and an effective porosity of 17% and is under a hydraulic gradient of 0.0055 m/m. Calculate the specific discharge in m/s. Calculate the average linear velocity in m/s.
Determine the volume of the tank : A tank that volume is unknown is divided into two parts by a partition. One side of the tank contains 0.01 m3 of refrigerant R-134a that is a saturated liquid at 0.8 MPa, while the other side is evacuated. The partition is now removed, and the refrig..
Human body-what is the oxygen pumping rate in g per minute : Consider human body. A 70 kg human has about 5 L of blood and it is pumped by heart at about 5.2 LPM (liter of liquid blood per minute). At any given time, the lungs transfer oxygen from alveoli to blood capillaries and the oxygen concentration in bl..
Consists of two chambers separated by a frictionless piston : The double-acting piston cylinder shown below consists of two chambers separated by a frictionless piston. The piston is initially locked in place, dividing the device into two equal 1 m3 sub-chambers. Side A contains water at 90°C and a quality of x..
Calculate the effective flow area in terms of theta : The flow pattern at the exit of a radial centrifugal compressor impeller shows a jet-wake behavior. In order to estimate the blockage, we assume that the wake region has zero momentum and is of angular extending theta (per passage) at the impeller ex..
The compressor and turbine of a simple gas turbine : The compressor and turbine of a simple gas turbine each have isentropic efficiencies of 80%. The compressor ratio is 12. The minimum and maximum temperatures are 290 K and 1400 K, respectively. On the basis of an air-standard analysis, compare the va..
The double-acting piston cylinder-frictionless piston : The double-acting piston cylinder shown below consists of two chambers separated by a frictionless piston. The piston is initially locked in place, dividing the device into two equal 1 m3 sub-chambers. Side A contains water at 90°C and a quality of x..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd