How would you develop a looping program in mips that will

Assignment Help Electrical Engineering
Reference no: EM13344464

How would you develop a looping program in MIPS that will take a series of decimal numbers and arrange them in ascending order from smallest to largest. The sequence of nine numbers are: 5, 3, 8, 9, 2, 4, 1, 7, 6, 3, 8 Once the numbers are ordered correctly, they do not have to be printed out. In other words, they could be left in memory.

Reference no: EM13344464

Questions Cloud

How much heat is produced in burning 7 mol of rmc2 rmh2 : how much heat is produced in burning 7 mol of rmc2 rmh2 under standard conditions if both reactants and products are
Assume a thermocouple which supplies the input to an : assume a thermocouple which supplies the input to an analog input module generates a linear voltage from 20mv to 50mv
A closed rigid tank whose volume is 15 m3 contains : a closed rigid tank whose volume is 1.5 m3 contains refrigerant 134a initially a two phase lipuid-vapor mixture at 10c.
If the aluminum block is initially at 25 what is the final : suppose that 1.04 of rubbing alcohol evaporates from a 57.0 aluminum block. if the aluminum block is initially at 25
How would you develop a looping program in mips that will : how would you develop a looping program in mips that will take a series of decimal numbers and arrange them in
A proton in a linear accelerator has a de broglie : a proton in a linear accelerator has a de broglie wavelength of 115 rm pm. what is the speed of the
A gas occupies 404 l at 860 torr and 10c what volume will : a gas occupies 4.04 l at 860 torr and 10c. what volume will it fill if the pressure is changed to 731 torr and the
What volume in milliliters of a 00992 m naoh solution is : what volume in milliliters of a 0.0992 m naoh solution is required to reach the endpoint in the complete titration of a
The cross section of a cottage 20 ft wide is an isosceles : the cross section of a cottage 20 ft wide is an isosceles triangle. if the slope of a side is 1.75 and there is a

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine un-damped natural frequency

Find the transfer function C/R and then determine un-damped natural frequency ωn, damping ratio ζ and percentage maximum overshoot Mp for a unit step input.

  Modify counter except for hooking logic to inputs and output

Assume you have a 3-bit pre-packaged counter. You cannot modify thecounter except for hooking logic to the inputs and outputs. Thecircuit has synchronous load and synchronous reset control inputs.The loadable inputs are a2, a1, and a0 (with a2 as ..

  Determine the surface charge densities on inner conductor

A coaxial air line has an inner conductor diameter of 2mm and the inner diameter of the outer conductor is 4.6mm. A voltage of 1 V is applied to the inner conductor. Determine the surface charge densities on the inner conductor

  Whether the variable x is a three-bit unsigned integer

A special external data signal (DATA_READY) is asserted whenever each of the bits for X are available. In addition, another special signal (ENCODE) is asserted during the transmission of the data X indicating whether 2X+3 or 3X+1 should be compute..

  What will be magnetic moment of the combination

A bar magnet is cut into 2 parts ,one part is kept over the other so that the pole c2 is above c1. IF M is magnetic momentof the magnet. What will be magnetic moment of the combination

  Explain what is the fundamental frequency of the spectrum

What is the fundamental frequency of the spectrum of the square wave? What is the magnitude of the fundamental frequency component of the spectrum of the square wave?

  Determine the electric field intensity e due to charge line

Find the electric field intensity E, at (ρ=0,φ=a, z=h) due to a uniformly charged line of line charge density of ρLC/m and radius a lying inthe xy plane at z=0.

  Design a synchronous tdm carrier to support 30 channels

Asssume that you are to design a synchronous TDM carrier to support 30 voice channels using 6-bit samples and structure similar toT1.Determine required bit rate

  Determine the rotational power loss in hp

A shunt dc motor has RA = 0.1-ohm and VT = 440 V. For an output power of 16.1 hp, nm = 1,213 rpm and IA = 103 A. The field current remains constant. Find the the rotational power loss in hp.

  What form of linear distortion is introduced by the channel

Two components of linear distortion produced by transmitting asignal through an LTI (linear time invariant) system: Amplitude distortion - the frequency components of the input signalare transmitted through the system with different amounts of gain..

  What is the velocity of propagation of the cable

A slotted line is used to measure the voltage maximums and voltage minimums on a transmission line with a characteristic impedance of 50 . The voltage maximum is measured as 7.5 V and the minimum is 5 V. The line is terminated with a purely resist..

  Find the potential drop from x2 to x1 in terms of p1 and p2

Consider a 1-D semiconductor system when we have a perfect balence of drift and diffusion of holes. that is the total Jp=Jp, diffusion +Jp, drift = 0. P(x=x1)=p1, P(x=x2)=p2. find the potential drop from x2 to x1 in terms of p1 and p2

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd