Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Use the following truth table of function f for parts (a)-(g) below.x y z f(x, y, z)0 0 0 10 0 1 10 1 0 00 1 1 01 0 0 11 0 1 11 1 0 01 1 1 1
(a) Write f as a minterm list (that is, in the form fm(*)).
(b) Write f as a canonical sum-of-products.
(c) Simplify the expression from part (b).
(d) Write f as a maxterm list (that is, in the form fM(*)).
(e) Write f as a canonical product-of-sums.
(f) Simplify the expression from part (e).
(g) Simplify f using a 3-variable Karnaugh map.
A 200hz(mode 1), 50% duty cycle square wave is to be generated at Timer0 interrupt. a) write a main program that would set Timer0 and the interrupt,and then force the first interrupt.
The reliability performance of each microprocessor is based on the exponential reliability distribution with the following failure rates: A = 23.5 × 10^-3 , B = 12.5 × 10^-4 , C = 12.5 × 10^-4 and D = 23.5 × 10^-3
4.What is the fundamental benefit of PLC controls over manual controls 5.Describe the differences between the two methods of scanning during PLC logic solving. Which method holds the advantage over the other
Select f and K so that the steady-state error to a ramp input is less than or equal to 25% of the input magnitude.Determine the percent overshoot for a step input for the design selected in part (b).Use MATLAB to plot y(t) for a step input R(s).
The tuning control is required to provide a uniform, linear change in frequency for a fixed rotation of the knob, e.g., 25 kHz per revolution at any operating frequency. You are considering three options for controlling the frequency
A majority function is generated in a combinational circuit when the output is equal to 1 if the input variables have more 1's than 0's. The output is 0 otherwise. Design a 3-input (A, B, C) majority function. Use K-maps to simplify the circuit. D..
Design a combinational circuit with four inputs, x,y,w, and z, and four outputs: A, B, C, and D. When the binary input value in decimal is 3,5,6,9,10 or 12, the binary output value is one less than the input value, otherwise it is one greater than..
A delta connected load consists of three identical impedances Z=45 at 60 degrees per phase. It is connected to a three phase, 208-V source by a three phase feeder with conductor impedance Zfeeder=(1.2+j1.6) Ohms per phase.
Determine the minimum signal to noise ratio (s/n) in dB required in each communication channel to achieve a data rate of 270 kbps?
Laplace transforms enable interpretation and manipulation of different signals by viewing these signals as either time domain signals/pulse or else frequency domain representations
When the starter motor, which draws 90A, is running the terminal voltage drops to 11V. What is the internal resistance of the battery What percentage of the chemical power is delivered to the starter motor
A micrometer caliper is used to measure the diameter of a bolt and a reading of 0.768 inches is obtained. Based on this measurement, find the smallest possible diameter and the largest possible diameter.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd