Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Sequence detector: 011010Output, seven segment display
if 011 is detected: "3"if 011010 is detected: "6"otherwise: "0"
A) What is the state diagram, extra states?B) transition table, (8 states with 2 unused that need to be addressed?)C) K-MapsD) EquationsE) Logic Diagram: replace basic logic gates with NAND and Inverters. Still use flip-flops and other necessary chips.
An electric flux of 151 Nm2/C passes through a flat horizontal surface that has an area of 0.715 m2. The flux is due to a uniform electric field. What is the magnitude of the electric field if the field points 10.3° above the horizontal
Assume that the memory locations M[$20], M[$21] and M[$22]. Write a 68HC11 assembly language program (with lots of comments) that will determine the sum of the largest two numbers and store its value in M[$23].
An LED with a rated range of VF = 1.4 V to 1.8 V at IF = 20 mA is connected to a driver circuit with a peak output of 14V. What value of current-limiting resistor would be needed to limit the LED current to a maximum value of 20 mA
Implement the carry-out and sum functions for a 1-bit full adder using a 3-to-8 decoder block with active-low outputs and additional gates (what gate types should be used). Complete the truth table and draw the circuit diagram
An electronic PI temperature controller has an output p of 12 mA when the set point equals the nominal process tmperature. The controller response to step change in the temperature set point of 3 mA (equivalent to a change of 5 degrees F) is shown
1) Determine the transfer of second-order highpass filter with a cutoff frequency of 900 Hz and passband gain of 1 using a butterworth type. 2) Design a filter for your transfer function from question.1 using the sallen-Key topology.
a sinusoidal voltage has a peak value of 15V, a frequency of 500Hz, and crosses zero with a positive slope at t=0.1 ms. write an expression for the voltage using a cosine function in terms of t and constant pi.
design a 4th order Butterworth band-pass filter, using a low-pass filter followed by a high-pass filter, to extract the 1200Hz and 1500Hz components from the signal x(t) a. Determine the cut-off frequencies of the low-pass and the high-pass filters..
Develop a state diagram for a sequential circuit that has two input terminals (W and X) and two output terminals (Y and Z). When three consequtive 1's are detected on W, Y will become 1.
The contects of a six-bit register are initially 100101. The register is shifted four times to the right, with the serial input being 1101. What are the contents of the register after each shift
Design a Moore sequential machine that has one input X and one output Y. Whenever X changes from 0 to 1, Y should become 1 for two clock cycles and then return to 0 - even if X is still 1. For example, given an input sequence X=0110101001.
A process has dynamics G(s)=1/(4s^s+s+1). Apply a unity negative feedvack controller of the form G.c(s)=1/(s+b). (a) Report the transfer function T(s) of the closed-loop system. (b) Report T(s) to 2nd order and report the reduced transfer function T..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd