How to make wien bridge tune to different frequencies

Assignment Help Electrical Engineering
Reference no: EM131037717

The objective of assignment is to design and simulate Wien Bridge oscillator using IC op-amp and calculate of its frequency oscillation.

Specification: Different specification of design for each student. Please refer Table 1.

1. Power supply = ± 12V.

2. Power consumption, < 10mW.

3. Oscillation frequency is targeted between 100 KHz to 200 KHz.

Deliverables:

1. You are expected to design a Wien Bridge oscillator by connecting the variable resistor, Rf = 10 kΩ) resistive to the inverting inputs. Adjust Rf to observe the waveform output.

2. Observe the waveform at both inputs and output point and measure the peak to peak voltage.

3. Compute the expected frequency of oscillation from the equation. Compare the calculation and simulation results.

4. Show the design steps in details and calculate the components value.

5. Simulate the designed circuit using LTPSICE to verify its operation.

6. Discuss how to make a Wien Bridge tune to different frequencies.

7. You are expected to present your results in the form of a Technical Report.

ASSESSMENT CRITERIA:

Technical Report

I) Clear technical theory details related to the assignment.

2) Proper explanation of the design and working principle of the circuit.

3) Modeling and simulation of the designed circuit using LTSPICE.

4) Discussion and Conclusion.

Reference no: EM131037717

Questions Cloud

Question regarding the unit excise tax : For the next seven questions, suppose a per unit excise tax of $80 per laptop is levied on the consumers.
Investigate the signal currents and voltages : Amplifier circuit. Knowledge of this signal distribution is very useful in designing the circuit so as to allow for the equired signal swings. Figure P8.73 shows aCMOS cascode amplifier with all dc voltages replaced with signal grounds. As well, w..
Compare labor relations system of u.s. with another country : Compare the labor relations system of the U.S. with another country in which unions are either limited or absent. How do the two countries' labor relations systems differ in terms of their history, laws, and practices?
Problem regarding the project irr : For the project shown in the following table, calculate the internal rate of return. Then indicate, for the project, the maximum cost of capital that the firm could have and still find the IRR acceptable. What is the project's IRR?
How to make wien bridge tune to different frequencies : Compute the expected frequency of oscillation from the equation. Compare the calculation and simulation results and discuss how to make a Wien Bridge tune to different frequencies.
What are the ethical issues that are involved : What are the ethical issues that are involved? Be sure to distinguish between issues that are primarily right-and-wrong versus those that are right-and-right issues in which there are simply tough trade-offs of appropriate competing values.
Problem regarding the demand for smartphones : Cell phone data plans are most useful when used with a smartphone, and smartphones are most useful when used with a data plan. As the price of data plans falls, the demand for smartphones will:
The allowable voltage range at the output : Consider the cascode amplifier of Fig. 8.33with the dc component at the input VI = 0.6 V, VG2 = 0.9 V, VG3 = 0.4 V, VG4 = 0.7 V, and VDD = 1.3 V. If all devices are matched, that is, kn1 = kn2 = kp3 = kp4, and have equal /Vt/ of 0.4 V, what is th..
What are the reporting responsibilities of the auditee : Research reporting responsibilities, especially the Office of Management and Budget (OMB) Circular A-133.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How to calculate critical resistance

How to calculate critical resistance?

  Write a program to genrate a square wave

assuming XTAL=11.0592 MHz,write a program to genrate a square wave of 20 Hz frequency on pin2.3?

  Sketch a layout that matches two capacitors of unit size

sketch a layout that matches two capacitors of unit size 8 and 3.75.The key is to match the perimeter-area ratio.Assume the unit capacitors are sized 4um*4um. Make sure to give the non-unit capacitor dimensions.

  Calculate the q-point

Design a CE amplifier to meet one of the sets of specifications below.  Assume RI = 0 and R3 = ∞ for your calculations and use standard resistor values.  Calculate the Q-point, Av, Rin and Rout.  Simulate your design and compare with your calculation..

  What purpose does the reactive power serve

An induction motor absorbs an apparent power of 500 kVA at a power factor of 75%, calculate the active and reactive power absorbed by the motor, what purpose does the reactive power serve

  Determine what would be the piv for the diodes

A ripple voltage of 0.4Vpp is required. Diodes are assumed to have 0.7V drop. Determine the 60Hz transformer secondary voltage and the size capacitor required. What would be the PIV for the diodes

  Write down frequency components of the received am signal

An AM signal has an unmodulated carrier voltage VC = 10VP, a load resistance of RL = 10, and a modulation index of m = 1. Determine  Write down the frequency components of the received AM signal.

  Derive an expression for ripple voltage

Derive an expression for ripple voltage of a three-stage Cockcroft-Walton Circuit - Explain with diagrams, different types of rectifier circuits for producing high d.c. voltages.

  What is the rotation speed of the disks in rpm

A given application is reading and writing 32KByte files on a disk that has a data transfer rate of 150MByte/s. Measurements have shown that this disk incurs an average seek time of 6.7 msec and needs an average of 11.08 msec to complete a read or..

  Present a block diagram of the design

Students present a block diagram of the design. Students submit a plan for testing the circuits in order to demonstrate that it meets the specifications.

  Investigate the performance of apd controller

Consider the following second order transfer function: G(s) = 2/s2+0.4s+1.. Use MATLAB Simulink software to investigate the performance of APD controller with a fixed proportional gain of Kp=0.2. Demonstrate the effect of changing the value of Kd ..

  Determine the circuits reactive power and power factor

A series-connected load draws a current i(t)=4cos(100pt + 10°) A when the applied voltage is v(t) = 120cos(100pt-20°) V. Determine a) The circuit‘s apparent power b) The power factor, pf c) The value of the impedance Z

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd