How much time is required to bring the density of dissolved

Assignment Help Mechanical Engineering
Reference no: EM131092755

14.40 A large sheet of material 40 mm thick contains dis- solved hydrogen (H2) having a uniform concentration of 3 kmol/m3. The sheet is exposed to a fluid stream that causes the concentration of the dissolved hydrogen to be reduced suddenly to zero at both surfaces. This surface condition is maintained constant thereafter. If the mass diffusivity of hydrogen is 9 X 10-7 m2/s, how much time is required to bring the density of dissolved hydrogen to a value of 1.2 kg/m3 at the center of the sheet?

Reference no: EM131092755

Questions Cloud

Concept in order to balance the economy : The spending multiplier’ was introduced Describe what it is and how it works. Explain why is it important for the Federal Reserve to consider this concept in order to ‘balance’ the economy?
Find the resulting equilibrium level of inflation : Economics 312/702 -Macroeconomics: Problem Set 4. Suppose that the policymaker can commit implementing a rule xt = but for some b. Find the resulting equilibrium level of inflation
Explain the development of american exploration and science : Explain the development of American exploration and science and how they contributed to nationalism in the1850s. Explain why and how the debate over slavery became increasingly heated during the1850s.
Economic growth and public policy : Suppose Yamahonda, a Japanese-owned motorcycle manufacturer, builds a production plant in Alabama. This is an example of foreign investment in the United States. Which of the following policies are consistent with the goal of increasing productivity ..
How much time is required to bring the density of dissolved : If the mass diffusivity of hydrogen is 9 X 10-7 m2/s, how much time is required to bring the density of dissolved hydrogen to a value of 1.2 kg/m3 at the center of the sheet?
Discuss the swot technique : Discuss the SWOT technique with respect to at least one element each that you identified in two of the four quadrants. Explain how this knowledge could be used in the strategic planning process within your selected company. (See attached SWOT anal..
Cutting back government spending : As to how the federal deficit would be cut back, the economists rule out tax increases. Instead, the cuts must come on the expenditure side with the average growth of federal expenditures - including interest payments on the national debt - kept b..
How much of the tax burden does each bear : Using a demand function of P = 7 – 2Q and a supply function of P = 4 + Q, and when adding an unit excise tax of $1.50, determine the following: Who really bears the burden of this tax? I. Consumers II. Producers or III. Both. How much of the tax burd..
Compare confederate and union strategies during the war : Compare and contrast Confederate and Union strategies during the war. What did each hope to achieve militarily and how did each hope to achieve it?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  2 forces are acting -20 and 20 ft away from the origin each

2 forces are acting -20 and 20 ft away from the origin. each force is 1000 lbf and they are acting 60 degrees from the

  What is the efficiency of this heat engine what is the

a heat engine is composed of of a monatomic ideal gas which runs in the following cycle at point a the pressure is 2.6

  Determine a the exergetic effectiveness and b the exergy

refrigerant 134a at -10degc 1.4 bar and a mass flow rate of 280 kghr enters an insulated compressor operating at steady

  Determine for the nozzle the velocity of the steam

Water vapor at 100 lbf/in^2, 500 degrees F and a velocity of 100 ft/s enters a nozzle operating at steady state and expands adiabatically to the exit, where the pressure is 40 lbf/in^2. If the isentropic nozzle efficiency is 95%, determine for the no..

  Problem regarding the ideal gas model

At steady state, air at 200 kPa, 528C and a mass flow rate of 0.5 kg/s enters an insulated duct having differing inlet and exit cross-sectional areas. At the duct exit, the pressure of the air is 100 kPa, the velocity is 255 m/s, and the cross-sec..

  Slow expansion is performed while there is heat transfer

a pistoncylinder contains water with quality 75 at 200 kpa. slow expansion is performed while there is heat transfer

  Cnsider the posts in their initial unyielded state if p

the rigid beam shown is supported by three cylindrical posts which rest on a rigid base a 20 mm dia. brass post at be

  Explain what is the acceleration of the aircraft

What is the acceleration of the aircraft (in m/s2)? How long does it take the aircraft to reach its take-off speed?

  Assume the pressure in the air above the water was 40 kpa

during a certain movie on cavitation dr. kavi tae shun held in his hand a closed cylinder filled with water and air. he

  Calculate the critical radius for a nickel embryo nucleus

calculate the critical radius for a nickel embryo nucleus that is undercooled 150 degrees c. the melting point of ni

  A late-model hummer has a frontal profile area of 31 m2 and

a late-model hummer has a frontal profile area of 3.1 m2 and a cd of 0.47. it is moving at a steady speed of 75 mph. a

  What is the nature of conditions

If the bottom surface is colder than the top surface, what is the nature of conditions within the container? For example, will there be vertical gradients of the species (O2 and N2) concentrations? Is there any motion of the air? Does mass transfe..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd