How much time elapses before the inductors stored energy

Assignment Help Electrical Engineering
Reference no: EM13277981

If a constant voltage drop of 16 V is maintained across an inductance of 140 mH that was initially carrying 1.6 A of current, how much time elapses before the inductor's stored energy reaches 590 mJ?

Reference no: EM13277981

Questions Cloud

Determine the distance between given points : Two points in a rectangular coordinate system have the coordinates (4.7, 2.5) and (-2.5, 4.7), Determine the distance between these points
What was the initial speed of the arrow : An archer shoots an arrow horizontally at a target 15m away. What was the initial speed of the arrow
Determine if the hidden element is an inductor or capacitor : A circuit element hiden inside a paper bag draws a current that varies with time t (in seconds) according to the current function i(t) = 0.032 sin(2350·t) Amps, while the voltage drop across this element is given by the function v(t) = 8.27 cos(23..
What is the location of the fly in polar coordinates : A certain corner of a room is selected as the origin of a rectangular coordinate system. what is the location of the fly in polar coordinates
How much time elapses before the inductors stored energy : If a constant voltage drop of 16 V is maintained across an inductance of 140 mH that was initially carrying 1.6 A of current, how much time elapses before the inductor's stored energy reaches 590 mJ?
Calculate the balls rotational kinetic energy : A bowling ball of mass 7.00kg is rolling at 3.00m/s along a level surface. Calculate the ball's rotational kinetic energy
Explain a typical titration curve : The figure shown below shows a typical titration curve for 0.1 M NaOH with 40 mL of 0.05M oxalic acid (H2C2O4). The first equivalent point is ~ at 9 .0 mL and the second equivalent point is at ~18 mL.
Devise a system that will convert the temperature range : Devise a system that will convert this temperature range into an 8-bit digital word with conversion from 00H to 01H at 200°C and from FEH to FFH at 350°C . An ADC is available with a 2.500-V internal reference.
What is the volume of the interior of the house : A house is 30.0 ft long and 25.0 ft wide, and has 8.0 ft high ceilings. What is the volume of the interior of the house

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the line current-input power and developed torque

A 74.6-kW, three phase, 440-V (line to line), four pole, 60-Hz induction motor has the following (per phase) parameters referred to the stator circuit: Rs=0.06-Ω, Rr=0.08-Ω, Xs=0.3-Ω, Xr=0.3-Ω, Xm=5-Ω The no-load power input is 3240-W at a current ..

  Determine what is the common-mode rejection ratio

What is the common-mode rejection ratio (in dB) if the output voltage is measured to be 2.0 Vp-p when the input terminals are connected together and a 0.1 Vp-p voltage is applied between the inputs and ground.

  What are the consequences with regard to fc

A given low pass filter has a cutoff frequency fc and a sample frequency fs. The sampling period is T = 1/fs. In implementing the filter it is essential that the evaluation of the difference equation be completed in less.

  Explain what determines which region the transistor is in

What is the difference between the saturation and active regions of a BJT. What determines which region the transistor is in.

  Find the magnitude of the voltage at the sending end

Assume the factory described in the previous problem is fed from a line having an impedance of 0.02 + j0.16-ohm. The voltage at the factory is maintained at 480 V(rms). Find the average power loss in the line before and after the load is added.

  Build circuit for parking deck where binary counter count up

build a circuit for a parking deck where a binary counter counts up when a car comes in and down when one leaves. There can only be a maximum of 40 cars in the parking deck before an LED turns on to notify the parking deck is full.

  What is the maximum distance between pump and power source

You have a 120 VAC motor pump system. The system will work in a voltage range from 100 to 130 volts. you can count on the minimum voltage from the supplier to be 115 VAC. The wiring will consist of #14 awg which has a resistance of 2.5 ohms/1000 f..

  What is the maximum allowable value of r2

For the amplifier in Fig. P4.20, the maximum value of VS is 2 V and the op-amp can deliver no more than 100 mA. (a) If +-10 V supplies are used, what is the maximum allowable value of R2 (b) Repeat for +-3 V supplies.

  Calculate the mmf when the machine operates

calculate the mmf when the machine operates at rated voltage at full load? PLease explain how to get the solution to this problem?

  Determine the width of the depletion region

A pn junction with Nd=4x10^16 cm^-3 and Na=3 x 10^15 cm^3 experiences a reverse bias voltage of 1.6V (a) Determine the width of the depletion region and the junction capacitance per unit area

  Find the value of peak amplitude in a constellation diagram

A constellation diagram has four points located at (2,2), (-2,2), (-2, -2), and (2, -2) on the I(in-phase)-Q(quadrature phase) plane. Find the value of peak amplitude and the type of modulation this diagram represents.

  Determine general solution for charge q

RC series circuit c=10,r=1,vs=15 and intial capictor charge q(0)=0.01. write standard form of the diffierential equations which describe the capictors charge q(t) t>0, obtain integration factor u(t),and determine general solution for q(t)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd