Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A hot-air balloon is rising upward with a constant speed of 3.86 m/s. When the balloon is 9.27 m above the ground, the balloonist accidentally drops a compass over the side of the balloon. How much time elapses before the compass hits the ground?
Two charges, q and 5q, are separated by a distance d in air. Assume that the charge q is at the origin and the charge 5q is at x = d. A third charge is placed on the x axis so that the entire system is in equilibrium (there is no net force on any ..
In a balanced three-phase system the Y-connected impedances are 3∠60°Ω. If V_bc=480∠-75° V, find current of phase "b" in polar form.
Design a datapath that consists of four four-bit, general-purpose registers and one four-bit processor status word (PSW) register. There are four status bits, carry, overflow, sign, and zero; these will be stored in the four bits of the PSW.
design a new p-type semiconductor material. Acceptor density is Na=5x1015 cm^-3 and there are no donors are present in the material. The effective densities of states for this material is given as Nv=1.8x10^19cm^-3
A 2.0 kg particle moves along the x axis. Its position varies with time according to x = t + 3.0t^3, Where x is in meters and t is in seconds. (a) Find the work done on the particlein the interval t = 0 to t = 1.70s.
Now, suppose that an initial voltage of 1V is present at the capacitor at zero time (t = 0). Will the behavior of the circuit when a step input is applied still yield an exponential rise or will the behavior be of some other type
1-If the AB current in a Y-connected load has an angle of -14°, what is the angle of the a-phase current. (0 decimals in degrees) 2-If the current of the a-phase in a Y-connected load has an angle of -73°
Given a 1-phase 50 kVA 12.47 kV pf = 0.8 lagging static load a. Modeling the load as constant complex power, determine the correct value for S and I. b. Modeling the load as constant complex impedance, determine the correct value for Z and I.
1.The S12G128 CPU board has one IRQ pin. You have four devices that will request interrupt service. How do you determine which device(s) need service 3.A communications channel has a bandwidth of 2,000 Hz and a signal-to-noise ratio (SNR) of 40 dB.
The output/ input of a system is 30dB. detrmine the ratio Express x(t)=4*cos(100*t-45)+ 2*cos(250*t+30) in terms of exponential functions Then Detrmine the phase angles(in degrees) of the two frequency components of x(t).
design a state table and diagram for a campus id consisting of 6 letters. when converted to binary using ascii code the id has 7-bits for each letter . e.g campus id TSHMUD(T = 1010100, S = 1010011, H = 1001000, M = 1001101, U = 1010101, D = 10001..
A proportional control system is to be used to control the wing flap of a jet airplane. The wind load is expected to cause as much as 600 in-lb of torque. The system should be able to keep the flaps with 5o of the set point.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd