How much the power rating of a device has to be reduced

Assignment Help Electrical Engineering
Reference no: EM131295377

Assignment

Electronics Lab

DC Analysis of Transistor and DC Load Line

1. For the common emitter circuit shown below (see figure 1) the parameters are:

VBB = 4 V, RB = 220 kΩ, RC = 2 kΩ, VCC = 10 V, VBE(on) = 0.7 V, and β = 200. Calculate the base current (IB), collector current (IC), emitter currents (IE), the VCE voltage and the transistor power dissipation (PT). Show all work.

897_Common Emitter Circuit.jpg
Figure 1

2. In the CC circuit shown in Figure 2, calculate the following:

o IB
o IE
o VCE
o VE
o VB. Take β = 49 and VBE = 0.7 V.

869_The CC Circuit.jpg
Figure 2

For the circuit shown in Figure 3 below, draw the DC load line and locate its quiescent or DC working point. Show all work.

584_Circuit.jpg
Figure 3

The data sheet entry that lists how much the power rating of a device has to be reduced is the__________________.

In a common-emitter circuit, once the base current has been calculated, collector current can be determined by multiplying the base current by ________.

Reference no: EM131295377

Questions Cloud

Designing training for an international assignment : A human resources department needs to take into account a variety of practical matters when designing training for an international assignment. What should the department focus its training resources on when preparing employees for overseas assign..
What was the amount of the service cost for the year : The projected benefit obligation was $400 million at the beginning of the year and $429 million at the end of the year. At the end of the year, pension benefits paid by the trustee were $18 million and there were no pension-related other comprehensiv..
What is the hazard communication standard : What is the hazard communication standard? Explain how this standard applies to the workplace. What should employers do in order to be compliant with this standard? What are the possible implications to an employer for failure to adhere to this st..
Determine the possible tax consequences of each issue : Ballou Corporation distributes $200,000 in cash to its shareholders during the current year. Accumulated earnings and profits at the beginning of the year are $45,000, and current year earnings and profits are $105,000. Buddy owns 80% of n each of th..
How much the power rating of a device has to be reduced : For the circuit shown in Figure 3 below, draw the DC load line and locate its quiescent or DC working point. Show all work. The data sheet entry that lists how much the power rating of a device has to be reduced is the ______.
Competitive market equilibrium and demand : ECO 2023 Fall 2016 The four market arrangements and the characteristics of each and competitive market equilibrium and demand from the perspective of the representative firm
Determine the frequency at which the op amp saturates : Use an AC source and an AC analysis with a linear sweep from 100 kHz to 1 MHz. Use the cursor to determine at what frequency the magnitude of the output reaches |15|V.]
State income tax deduction : Pierre, a cash basis, unmarried taxpayer, had $4,430 of state income tax withheld during 2016. Also in 2016, Pierre paid $1,108 that was due when he filed his 2015 state income tax return and made estimated payments of $3,101 towards his 2016 state i..
Analyze all of the costs and benefits of outsourcing it : Analyze all of the costs and benefits of outsourcing IT, and present at least four well-supported reasons why the company should keep the department. Using all of your knowledge up to this point and any external sources necessary, create a present..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Draw logic diagram of four-bit register with four flip flop

Draw the logic diagram of a four-bit register with four D flip-flops and four 4 X 1 multiplexers with mode selection inputs s1 and s0. The register operates according to he following function table

  Find leakage resistance on the primary and secondary sides

The resistance readings collected after the open and short circuit tests are the resistance reading when the transformer is operating with DC. Supposedly, the resistance collected should be the same as the leakage resistance, distributed with the ..

  Determine the transition point of the driver transistor

Consider the NMOS inverter with saturated load in given Figure (a). - Determine the transition point of the driver transistor.

  Determine what is the built in potential of the diode

A silicon diode has a doping profile such that ND = ax3. What is the depth of the junction assuming the p side is uniformly doped with NA per cubic cm. Assume the x origin is at an ideal ohmic contact on the n side of the diode.(assume T=300K).

  Explain why this is generally not a good idea

Compare the result with that of a cascode stage for a given bias current (IC1) and explain why this is generally not a good idea.

  Find the no load speed-stalled torque and stalled current

The resistance of the coil is 0.2 ohm. The inductance of the coil is 1.2e-4 H. The rotor inertia is 1.0e-5 kg m2. The current to torque gain is 0.03 Nm/A. The friction torque is 0.09 Nm. A 12 V voltage source is applied to the motor.

  What is the final velocity of the other puck

Consider the collision between two hockey pucks in the figure below. They do not stick together. Their speeds before the collision are v1i = 26 m/s and v2i = 11 m/s. It is found that after the collision one of the pucks is moving along x with a sp..

  What are some possible disadvantages of using the 318

The LM318 is a much faster op amp than the LM741C. In what applications might the 318 be preferred to the 741C? What are some possible disadvantages of using the 318?

  What does a carry-out in the fifth place indicate

Assume that you are adding two 4-bit numbers. What does a carry-out (in the fifth place) indicate. Does this carry-out indicate something different when we add two positive numbers, a positive and negative number, or two negative numbers.

  How do these gains change if the load is changed to 25

Compute the power gain, the available power gain, and the transducer power gain.

  Write a verilog user-defined primitive

A majority logic function is a Boolean function that is equal to 1 if the majority of the variables are equal to I. equal to 0 otherwise. Write a Verilog user-defined primitive for a four-bit majori-ty function.

  Determine its voltage-ratio and the kva rating

Mark on the diagram, the magnitudes and relative directions of the currents in the winding as well as in the input and output lines when delivering the rated kVA to load.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd