How much settlement has occurred when the time factor is

Assignment Help Civil Engineering
Reference no: EM13533380

The time factor for a doubly drained clay layer undergoingconsolidation is 0.2

a. What is the degree of consolidation (Uz) at z/H=0.25, 0.5,and 0.75

b. If the final consolidation settlement is expected to be 1.0m, how much settlement has occurred when the time factor is 0.2 andwhen it is 0.7?

Reference no: EM13533380

Questions Cloud

How far will the block travel from the base of the ramp : A block slides down a frictionless ramp of height 0.37 meters. How far will the block travel from the base of the ramp before the velocity reaches 2.3 m/s
Calculate the inductance of the inductor in this circuit : A series RLC circuit consists of a 49-ohm resistor and a 5.0-uF capacitor. what is the inductance of the inductor in this circuit
Compute with what force should you pull with rope horizontal : You're using a rope to pull a sled at constant velocity across level snow,with coefficient of kinetic friction 0.050 between sled and the snow. With what force should you pull with the rope horizontal
What direction should the boat have been headed to actually : To cross a river that is 1 km wide, with a current of 6km/h, a novice boatskipper holds the bow of the boat perpindicularto the far river bank, intending to cross to a point directly across the river from the launch point.
How much settlement has occurred when the time factor is : If the final consolidation settlement is expected to be 1.0m, how much settlement has occurred when the time factor is 0.2 andwhen it is 0.7?
Dynamic viscosity of the liquid between the plates : The relative velocity of two infinitely wide parallel plates thatare 1cm apart is 10cm/s. If the dynamic viscosity of the liquid between the plates is 0.001 N s/m2 what is the shear stress between the plates?
Calculate the consolidation settlement expected : For the profile shown, the initial ground water table is 5 ft belowthe surface. A proposed dewatering project will cause the watertable to drop 10 ft from the original level. Consolidation tests performed on clay samples produced the following result..
Find the normal strains in these two directions : If the normal stresses in the x and y direction are given byσx and σy, find the normal strains in these two directions.
Determine the rate of evaporation of water : Water is to be boiledat sea level in a 30 cm diameter stainless steel pan on top of a3-kW electric burner. If60% of the heat generated by the burner is transferred to thewater during boiling, determinethe rate of evaporation of water.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine whether it has an fcc or bcc crystal structure

Rhodium has an atomic radius of 0.1345nm and a density of 12.41g/cm^3. determine whether it has an FCC or BCC crystal structure

  Determine the theoretical discharge

A vertical triangular orifice in the wall of a reservoir has a base 0.9m long,0.6m below its vertex and 1.2 m below the water surface. Determine the theoretical discharge?

  Calculate the time needed for the particles to set

For a temperature of 10 degree C, calculate the time needed for the following particles to settle 0.3m: a) a 20um mineral particle with a specific gravity of 2.1, and b) a 2 um organic particle with a specific gravity of 1.2

  At what equal height above shorline should target be located

A surveyor is going to take a 5.5 mile sight across a lake from the top of one tower to a target on the top of another tower. It is desired to keep the line of sight 6 ft above the lake surface.

  Determine the tsp emission rate of the power plant

On a clear summer afternoon with a wind speed of 3.20 m/s measured at 100 m elevation, the TSP (total suspended solids) concentration was found to be 1520 ug / m3 at a point 2 km downwind

  Explain the difference between piezometer and tensiometer

Briefly explain the difference between piezometer and tensiometer with respect to the working principle, special design consideration and limitation of the instrument.

  Determine what should the viscosity of the model fluid be

In the late 1990's the U.S. Army Corps of Engineers designed an experiment to model the flow of the Tennessee river downstream of the Kentucky Lock and Dam.

  Design the flexural reinforcement for the member

A rectangular concrete beam of width b = 24 inches is limited by architectual considerations to a maximum total depth of h = 16 inches. it must carry a total factored load moment of Mu = 400 ft-kips.

  What is the maximum diameter that the rod can have

Under the right conditions, it is possible, due to surface tension, to have metal objects float on water. Consider placing a short length of a small diameter steel (sp. wt. =460 lb/ft^3) rod on a surface of water.

  Determine the final temperature and mass of the air

The tank is filled so quickly that the process is adiabatic and the seawater leaves the tank at 15oC. Determine the final temperature and mass of the air in the ballast tank.

  Determine particles position and the velocity of particles

The acceleration of a particle along a straight line is defined by a=(2t-9)m/s^2, where t is in seconds.At t=0, s=1m, and v=10 m/s. When t=9s, determine the particles position, the total distance traveled, and the velocity.

  Determine storage 1 hr later if average rates are given

The storage in a reach of river is 20,000 m^3 at a given time. Determine the storage 1 hr later if the average rates of in flow and out flow during the hour are 20 and 18 m^3/s, respectively

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd