How much power is being dissipated by the circuits

Assignment Help Mechanical Engineering
Reference no: EM131261709

A high-speed NMOS microprocessor has a 64-bit address bus and performs a memory access every 50 ns. Assume that all address bits change during every memory access, and that each bus line represents a load of 10 pF.

(a) How much power is being dissipated by the circuits that are driving these signals if the power supply is 2.5 V?

(b) 3.3 V?

Reference no: EM131261709

Questions Cloud

What happened to the corporate culture : Could you have anticipated that these results would have occurred? - -  What happened to the corporate culture?
What is the expected propagation delay of the logic gate : A logic family has a power-delay product of 100 fJ. If a logic gate consumes a power of 100 W, what is the expected propagation delay of the logic gate? The graph in Fig. P6.135 gives the results of a SPICE simulation of an inverter
Describe some way that group has changed over time : Identify and describe some way that group has changed over time. Discuss that change in terms of whether it was internal or external and then in terms of the specific factors that caused it.
How this religion defines the concept of good and evil : How are human beings viewed with regard to their characteristics and their place in the universe? If you cannot identify how this religion defines human beings, offer a suggestion as to why it doesn't.
How much power is being dissipated by the circuits : A high-speed NMOS microprocessor has a 64-bit address bus and performs a memory access every 50 ns. Assume that all address bits change during every memory access, and that each bus line represents a load of 10 pF.
Explain the benefits and possible drawbacks : Explain how measurement concepts discussed in the text and readings could be used in your research.- Why is it important to know the variables within your research study?
How has the power dissipation changed : Calculate the ratio of the drain current of the scaled device to that of the original device. How has the power dissipation changed?
Describe agents of socialization that have most influenced : Using the results of the quiz and the readings for this session, describe the agents of socialization that have most influenced your political values.
Provide details about your project that are designed : Provide details about your project that are designed to organize and manage all relevant resources to achieve specific goals and objectives.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Mixture of air and water at a temperature

A mixture of air and water at a temperature of 30ºC and a pressure of 750 mmHg has a relative humidity of 75%. The wet gas is compressed to 40 psia and cooled to 20ºC. How many cubic meters of original gas were compressed if 0.75 lb of condensate (wa..

  A flywheel can be considered as being composed of this disk

a flywheel can be considered as being composed of this disk and a rim. the rim weighs 322lb and has a diameter of 24in

  How much air pressure would be required to bubble air

Assume a pipe has an inside diameter of 1 square inch. How much air pressure would be required to bubble air though 25 feet of water?

  A 5-ft3 tank contains 06-gravity natural gas at 1500 psia

a 5-ft3 tank contains 0.6-gravity natural gas at 1500 psia and 100of. 200 scf of gas is released from the tank. this

  Some of the flow exits at an intermediate pressure at 2 as

argon gas flows steadily through a well-insulated turbine at the conditions shown below. some of the flow exits at an

  Design shear reinforcement and check bar cutoffs in tension

Design a rectangular beam (tension steel only). Determine bar cutoffs (use the graphical approach). Design the shear reinforcement and check bar cutoffs in tension zones if necessary.

  Find the sensible cooling load component from occupants

A church sanctuary is designed for an occupancy of 300 persons. The outside airflow rate is 15 cfm per person. The inside design temperature is 74°F and the outside air design temperature is 89°F. Approximate internal heat gains per occupant are 2..

  Calculate width of the tower at the given points

Use static equilibrium equations from your reference section to calculate the maximum tension and compression forces in the tower legs. Calculate width of the tower at the ¼ points.

  Take the gravitational acceleration to be 981ms2 also

a cylindrical tank of methanol has a mass of 40 kg and a volume of 51 l. determine the methanols weight density and

  Liquid water is cooled at a constant pressure of 200 kpa in

liquid water is cooled at a constant pressure of 200 kpa in a piston-cylinder device from a temperature of 110 degc to

  Products of the flash system are fed to distillation column

We are separating ethanol and water. All percentages are mol%. Find the q values and plot the feed lines. a) Feed is 60% ethanol and flashes in the column with v/f=0.37 b)Feed is 40% ethanol and is a two-phase mixture with liquid and vapor in equilib..

  The air can be modeled as an ideal gas determine the mass

a 0.15 m3 container is filled with 0.1kg of air. the pressure of the container is lower than its ambient pressure and

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd