How much petroleum coke must be added per 100 lb of basic

Assignment Help Mechanical Engineering
Reference no: EM13620617

A particular manufacturer of charcoal briquettes is contracted to create a product that contains no more than 0.1 mass fraction moisture and no more than 0.1 mass fraction ash. For one production batch, the basic material available has 12.4 mass percent moisture, 16.6 mass percent volatile material, 57.5 mass percent carbon, and 13.5 mass percent ash. To meet the specifications of its contract, the manufacturer plans to mix this material with a certain amount of petroleum coke that has a composition of 8.2% volatile material, 3.1% moisture, and 88.7% carbon by mass. How much petroleum coke must be added per 100 lb of basic material? Before solving, draw a flowchart and conduct a degree of freedom analysis.

Reference no: EM13620617

Questions Cloud

The two most prominent wavelengths in the light emitted by : the two most prominent wavelengths in the light emitted by a hydrogen discharge lamp are 656 rm nm red and 486 rm nm
Describe the population of interesthow many of the students : some students that attend college students work full or part time. how much did your working college friends each earn
What is the potential difference measured across the plates : the capacitor is disconnected from the battery and its plates moved so the distance between them is tripled.a. what is
For a normal distribution with a zero mean and standard : for a normal distribution with a zero mean and standard deviation of one use 10 random variables samples to compute the
How much petroleum coke must be added per 100 lb of basic : a particular manufacturer of charcoal briquettes is contracted to create a product that contains no more than 0.1 mass
Hooper printing inc has bonds outstanding with 10 years : hooper printing inc. has bonds outstanding with 10 years left to maturity. the bonds have an 7 annual coupon rate and
What is the maximum constant speed in miles per hour a : what is the maximum constant speed in miles per hour a stock car can travel around the 1000 ft radius turns that are
The number of customers at quiet morning bakery is : the number of customers at quiet morning bakery is believed to follow a poisson distribution with a mean of 2 customers
The wire is wound into a thin flat coil of many turns that : a piece of copper wire has a resistance per unit length of 5.50 10-3 ?m. the wire is wound into a thin flat coil of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Frm a normal distribution with mean 07515 cm and standard

assuming that the diameters of 1000 brass plugs taken consecutively from a machine form a normal distribution with

  Determine the heat transfer coefficient for laminar flow

Determine the heat transfer coefficient for laminar flow over this cylinder. First, at your discretion, select an available set of experimentally obtained data from the literature. Then, this would provide you with a set of Reynolds numbers.

  Saturated properties out of the evaporator

Assuming saturated properties out of the evaporator and condenser

  This nonresonant frequency is such that the ratio of the

in a series rcl circuit the generator is set to a frequency that is not the resonant frequency. this nonresonant

  Methane ch4 at 25 degree celcius 1 bar enters a furnace

methane ch4 at 25 degree celcius 1 bar enters a furnace operating at steady state and burns completely with 240 of

  Is the heat transfer one two or three dimensional is there

consider a medium in which the heat conduction equation is given in its simplest form as 1r2 ddrr2dtdr 1a dtdt a. is

  At the position of the negative charge what is the

three equal charges of magnitude q6.00 uc are located at three corners of a square edge length d2.9 cm. a negative

  A pulley with diameter d 27in weighs 80 lb it is mounted

a pulley with diameter d 27in weighs 80 lb. it is mounted on a diameter d 2-in axle. a weight of 1000 lb is to be

  Bleed steam enters this unit at 3000 kpa with a quality of

feedwater at 4000 kpa is heated at a rate of 6 kgs from 200degc to 245degc in a closed feedwater heater of a

  What angle with the horizontal should the pilots line of

the pilot of an airplane carrying a package of mail to a remote outpost wishes to release the package at the right

  Estimate the skin friction drag on the aircrafts fuselage

Determine whether laminar-to-turbulent transition occurs in the boundary layer of the fuselage. If transition occurs, where does it occur - Estimate the skin friction drag on the aircraft's fuselage.

  A rectangular intake air duct is 36 in wide and 24 in high

a rectangular intake air duct is 36 in. wide and 24 in. high. it runs for over 300 ft inside a warehouse and is at 50 f

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd