How much of the stem would protrude above the liquid surface

Assignment Help Mechanical Engineering
Reference no: EM13707010

When a hydrometer having a stem diameter of 0.30 in. is placed in water, the stem protrudes 3.15 in. above the water surface. If the water is replaced with a liquid having a specific gravity of 1.19, how much of the stem would protrude above the liquid surface? The hydrometer weighs 0.042 lb

Reference no: EM13707010

Questions Cloud

Heat is supplied to the airflow : As shown in the picture, air flows through a pipe. Heat is supplied to the airflow. The air at the inlet is 200kPa and 20 C with flow velocity of 5m/s. The exiting air is 180 kPa and 40 °C. The diameter of the pipe is 0.28 m. Determine (a) the volume..
Summer at a local produce stand exhibit a linear trend : Weekly sales for watermelons over the summer at a local produce stand exhibit a linear trend. The demand for weeks 1 through 10 was 91, 94, 95, 97, 92, 101, 107, 116, 113, and 121. Calculate the forecasts for weeks 2 through 10 using Holt’s double ex..
Coefficient of kinetic friction between the tires and road : A 2-Mg car has a velocity of v1 = 100 km/h when the driver sees an obstacle in front of the car. It takes 0.7s for him to react and lock the brakes, causing the car to skid. If the car stops when it has traveled a distance of 225m, determine the coef..
Piston-cylinder device contains helium gas : A piston-cylinder device contains helium gas initially at 150 kPa, 20 degrees C, and 0.4 m^3. The helium is now compressed in a polytropic process (PV^n = constant) to 400 kPa and 140 degrees C. Determine the heat loss or gain during this process.
How much of the stem would protrude above the liquid surface : When a hydrometer having a stem diameter of 0.30 in. is placed in water, the stem protrudes 3.15 in. above the water surface. If the water is replaced with a liquid having a specific gravity of 1.19, how much of the stem would protrude above the liqu..
Mass flow rate of steam produced by the evaporator : Orange juice at 5% total solids (by mass, wet basis) is concentrated in a single-effect evaporator to produce a concentrated juice with 40% total solids (by mass, wet basis). If the unit is producing 100 kg/hr of concentrated juice, how much fresh or..
Write an algebraic expression for each verbal expression : 2. Write an algebraic expression for each verbal expression. (a) a number m minus five (b) the sum of two times a number k and seven (c) two third of a number x plus ten (d) the product of 7 and m to the fifth power.
Write two ways of each algebraic expression in words : 1. Write two ways of each algebraic expression in words. (a) m + 7 (b) z - 11 (c) 5 × a (d) b ÷ 9
How many square meters is dance floor : The floor for the dancers is8.3 meters by 9.2 meters. The owners need to resurface that rectangle of the floor and need to know what the area is . How many square meters is this dance floor?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd