How much noise should we expect at output of the amplifier

Assignment Help Electrical Engineering
Reference no: EM13264787

if we have an amplifier whose spec. is 2nV/rtHz and the bandwidth of the amplifier extends from 100Hz to 10kHz, and the gain of the amplifier is 5, how much noise should we expect at the output of the amplifier

Reference no: EM13264787

Questions Cloud

Which break-even sales level is usually lower : For the same project, which break-even sales level is usually lower, the net present value breakeven or the income breakeven? Pick one
What is a black swan event : What is a Black Swan event? Does it ever make sense a priori to devote resources to preventing a black swan event?  Explain. Does it ever make sense a priori to devote resources to containing a black swan event should one occur?  Explain.
Calculate minimum distance from the start to the goal : Calculate the minimum distance from the start to the goal with passing all the checkpoints -Specification - The aim of this game is to arrive at the goal (G) from the start (S) with the shortest distance.
Compute the concentration of iron chloride contaminant : Calculate the concentration of iron (II) chloride contaminant in the original groundwater sample. Round your answer to significant digits.
How much noise should we expect at output of the amplifier : if we have an amplifier whose spec. is 2nV/rtHz and the bandwidth of the amplifier extends from 100Hz to 10kHz, and the gain of the amplifier is 5, how much noise should we expect at the output of the amplifier
Explain how many milligrams of digitalis should a 180 lb : At a dosage of 18 micrograms/kilograms body weight, how many milligrams of digitalis should a 180 lb. patient receivec
Favorite advertising subjects is subliminal advertising : One of my favorite advertising subjects is subliminal advertising. What do you think? Is it going on and we don't know it? Describe how you think subliminal perception could be used by marketers to the detriment of us consumers
What is the primary concern an investor should conside : when using the DDM to make an investment move, what is the primary concern an investor should conside at decision time?
Determine system bandwidth for subcarrier frequency spacing : An OFDM system employs 260 data subcarriers, 40 pilot subcarriers, and 34 guard subcarriers to transmit data through a wireless channel. QPSK modulation is employed for each subcarrier.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine what is the real signal to noise ratio

The signal noise ratio in an FM system is 4:1 The maximum allowed deviation is 4 KHz. How much frequency deviation is introduced by the phase shift caused by the noise when the modulating frequency is 650 Hz

  Find does sampling frequency meet the nyquist requirement

Five periods of the signal s(t)=sin(2500pi*t) are sampled at a sampling frequency of 4000 Hz. a. Does this sampling frequency meet the Nyquist requirement for the signal? b. How many samples are collected

  What is the maximum angle the shaft can turn

a 350° pot is connected to a shaft through a 3:1 gear ratio a. What is the maximum angle the shaft can turn b. What is the maximum difference in degrees from where the shaft is and where the pot reports is to be

  Calculate the triggering angle for the speed of 1000rpm

A 220 V, 1500 rpm, 11.6 A (armature current) separately excited motor is controlled by a single phase, full wave SCR converter. The armature resistance of the motor is 2 ohm. The ac source voltage is 230 V (rms) 60 Hz.

  What is the magnetizing inductance for the coil tested

A single-phase transformer has two 120V windings (primary) and one 240V windings (secondary) such that with the two primary in series properly (dot to no dot) the transformer is a 240:240V transformer. A test is run on one of the primary coils (one..

  Determine the required-size thw copper conductor

Determine the required-size THW copper conductor and overcurrent device rating required for a dedicated feeder supplying a 250 A noncontinuous linear load. Assume an ambient temperature of 30°C

  Analyzing the blink alive code

Analyzing the Blink Alive code - Embedded Systems Design

  Which should be the signal power in the given case

A cable technician tested the signal-to-noise ratio on the curb as 20 dBm. This means, if the noise power is at 1 mW, then the signal power should be 20 dB higher then that. If the noise power is 20 mW

  What was the peak current that would flow through the person

Assume the resistance of a human person was 500 ohms, if a person was struck by lightning with a peak voltage of 100,000 volts, what was the peak current that would flow through the person

  Design a finite state machine which recognizes pattern

Design a Finite State Machine which recognizes the serial pattern 111. Assume serial input is applied to input pin Sin and an output pin labeled Sout is 1 whenever the string is recognized.  a) draw a state diagram of your design.

  Calculate the reluctance of the magnetic circuit

A ‘c-core' inductor has a total air-gap length of 3 mm and a cross-sectional area of 100 cm2. Two coils are wound on the core - one of 500-turns and another of 250-turns. Assuming the iron reluctance, fringing flux and leakage flux to be negligibl..

  Find percentage of electriciy generated by fuel cell system

Fuel cell systems that also utilize the heat produced can achieve efficiencies approaching 80 percent , more than double of the gas-turbine based electruiical generation . Assume that 25 million houuseholds produce an average of 5 kw.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd