How much energy in horsepower islost by the water while flow

Assignment Help Civil Engineering
Reference no: EM13533351

A pipeline 1200ft long and 8in. in diameter hasat its inlet point 75ft of available hydraulic energy with respectto the reference level. The velocity in the pipe is 5fps; thepressure at its end is 12psi. The elevation at the end of the pipeis 10ft above reference level. How much energy in horsepower islost by the water while flowing through the pipe?

Reference no: EM13533351

Questions Cloud

Write a short class that shows an increment and decrement : A beam of length 3m with a non-uniform load of zero at end Aand 200N/m at end B i.e a vertical loading of 1/2 *200*3N with abending moment about A of 1/2*200*3*(2/3*3). The beam is supportedat end A for a distance of 0.5 m and a uniform suport force ..
You are designing a highway bridge : You are designing a highway bridge. In particular you aretrying to determine how to put the road surface on the bridge. Youlive in an area where the maximum summertime temperature is 40 degrees centigrade and the minimum winter temperature is -30degr..
What would be her recoil velocity : In a football game, a receiver is standing still, having just caught a pass. Before he can move, a tackler, running at a velocity of +3.1 m/s, grabs him. The tackler holds onto the receiver, and the two move off together with a velocity of +1.6 m/s
Convert the bearings to azimuths from north : Convert the bearings to azimuths from north and compute theangle . smaller then 180 degree. between successive bearings.
How much energy in horsepower islost by the water while flow : A pipeline 1200ft long and 8in. in diameter hasat its inlet point 75ft of available hydraulic energy with respectto the reference level. The velocity in the pipe is 5fps; thepressure at its end is 12psi.
Determine the volume of traffic across the bridge : A bridge has been constructed between the mainland and anisland. The total cost (excluding toll) to travel across thebridge is expressed as C=50+0.5V, where V is the number of veh/dayand C is the cost/vehicle in cents. The demand for travelacross the..
What is the average chear stress in the glue joint between : Two 1/2 inch rods are spliced together by glueing a 2 inch section of plastic pipe over the rods ends. If a tensile force P = 350 lb is applied to the spliced nylon rod, what is the average chear stress in the glue joint between pipe and the rods?
Calculate expected error l if a theodolite has direct : The bottom of a rectangular flume is 5mabove reference level. The depth of the water in the flume is 3m.The average velocity is 1.7 m/s. Compute the total hydraulic energyat the surface of the water and at the bottom of the flume.
Determine the critical point : The initial ultimate BOD after mixing of the Bergelmir Riveris 12.0 mg/L. The DO in the Bergelmir River after the wastewaterand river have mixed is at saturation. The river temperature is 10degrees celsius

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the downward deflection of the tray center

A tray rests on an extendible arm consisting of two steel tubes with two different outer diameters. The downward force at the tray center F0 = 1000 N. Determine the downward deflection of the tray center and the tilt angles of the tray about each ..

  Find the horizontal and vertical forces exerted on the poll

What is the maximum weight that can be suspended on a 16 Kg poll, 3/5 from the end. The maximum tension of the 30 degree guy-wire is 1500 N. Find the horizontal and vertical forces exerted on the poll by the hinge.

  Determine estimated unknown speed if the data were obtained

In an attempt to estimate the speed of a vehicle just before it hit a traffic signal pole, a traffic engineer measured the length of the skid marks made by the vehicle and performed trial runs at the site to obtain estimate if the coefficient of f..

  Determine what will be the discharge q at a depth

If sewage (assume the properties are the same as those of water) flows at a depth of 1.5ft in the pipe, what will be the discharge Q = 10.6 cubic feet/second

  What should be the length of an aluminum wire of 6 mm

What should be the length of an aluminum wire of 6 mm in diameter so it can be twisted one full turn without exceeding a shear stress of 42 MPa G = 27 GPa.

  Determine the magnitude of the largest elastic load p

the outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. if the yield stress for the steel is (sy)st = 640 MPa, and for the bronze (sy)br = 520 MPa determine the magnitude of the largest elastic load P

  Design lined trapezoidal channel to carry on longitudinal

Design a lined trapezoidal channel to carry 20 m^3/sec on a longitudinal sloe of 0.0015. The lining of the channel is to be float-finished concrete (n=0.015). Consider (a) the best hydraulic section and (b) the section with side slopes 1.5:1 (H:V)

  How many cubic yards of aggregate must be ordered

how many cubic yards of aggregate must be ordered for a road base 16 inches thick and 2000 feet long with a top width of 30 ft, if the side slopes are one on one, or 45 degree

  Determine what is the free flow speed on specific westbound

On a specific westbound section opf highway, studies show that the speed density relationship is u=uf *[1-(k/kj)^3.5]. It is known that the capacity is 4200hehicle/hr and the jam density is 210 veh/mile.

  Calculate the co-efficient of permability of the soil

In a falling-head permeability test the initial head of 1.5m dropped to 0.5m in 4 h the diameter of the standpipe being 5mm. The soil specimen was 200mm long by 100mm in diameter.

  Calculate the time average f of the total force tangent

Calculate the time average F of the total force tangent to the toad exerted on the tires during the 8 s. Treat the car as a particle and neglect air resistance.

  Find the probability that an 11 occurs for the first time

A pair of dice is tossed repeatedly. Find the probability that an 11 occurs for the first time on the 6th toss.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd