How much 235u was consumed on a ioooo-nautical-mile voyage

Assignment Help Mechanical Engineering
Reference no: EM13629399

The reactor on the nuclear ship Savannah operated at a power of 69 MW.

(a) How much 235U was consumed on a IO,OOO-nautical-mile voyage at an average speed of 20 knots?

(b) This is equivalent to how many barrels of 6.5-million-Btu/barrel bunker-C oil?

 

Reference no: EM13629399

Questions Cloud

The weights of professional baseball players follow a : the weights of professional baseball players follow a normal distribution with a mean of 200 pounds and a standard
A two-resistor voltage divider employing a 33-kq and a : a two-resistor voltage divider employing a 3.3-kq and a 6.8-kq resistor is connected to a 9-v ground-referenced power
A girl is standing at the edge of a cliff 111 m above the : a girl is standing at the edge of a cliff 111 m above the ground. she reaches out over the edge of the cliff and throws
If the oxygen undergoes adiabatic expansion through the : oxygen at 710 kpa and 365 celcius enters a staedy flow nozzle with a low velocity and leaves at 90 kpa. if the oxygen
How much 235u was consumed on a ioooo-nautical-mile voyage : the reactor on the nuclear ship savannah operated at a power of 69 mw.a how much 235u was consumed on a
The average time it takes college freshmen to complete the : the average time it takes college freshmen to complete the mason basic reasoning test is 38.3 minutes. the standard
The invoices are numbered from 0001 to 5000 complete the : the invoices are numbered from 0001 to 5000a. complete the list of the 10 invoice numbers that will be selected from
If density of air is 12 kgm3 at the inlet and 105 kgm3 at : a hair dryer is basically a duct of constant diameter in which a few layers of electric resisiotrs are placed. a small
A fighter jet lands on the deck of an aircraft carrier it : a fighter jet lands on the deck of an aircraft carrier. it touches down with a speed of 73.5 ms and comes to a complete

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The ultimate strengths in tension and compression are 210

a thin-walled cylindrical pressure vessel of 250 mm internal diameter and 5 mm thickness is subjected to an internal

  Knowing the acceleration of the truck is 1fts2 determine a

type your question herea 5000 lb truck is being used to lift a 1000 lb boulder b that is on a 200lb pallet a. knowing

  Applied loads and young''s modulus and poisson''s ratio

Applied Loads, Young's modulus, Poisson's ratio, The Young's modulus and the Poisson's ratio for copper are 124.8 GPa and 0.36 respectively. When a tensile load is applie to a 1.5cm diameter copper rod

  Determine the magnitude of the reaction force fa in the

to use the principle of superposition to determine the total deflection in a cylindrical rod due to a static loading.a

  A flow is described by velocity field where a 02 s-1 and

a flow is described by velocity field where a 0.2 s-1 and b 0.4 ms2. at t 2 s what are the coordinates of particles

  How the unknown constants in the original equation relate

for each of the situations below an equation is proposed as a model to relate an independent variable to a dependent

  Detrmine the differential equation of motion of the spool

a spool of mass m radius r and radius of gyration kg rolls without slipping on an incline whose angle with respect to

  Calculate the work in kjkg done per unit mass of the steam

steam at 2.5 mpa and 400 c enters an adiabatic steam turbine with a low velocity and leaves with a velocity of 180 ms

  In an accelerator protons emerge with velocity of 25 x 108

in an accelerator protons emerge with velocity of 2.5 x 108 ms. the accelerator is 0.8km long.a if the acceleration is

  The inlet area of the nozzle is 90cm2 determine a the mass

air enters an adiabatic nozzle steadily at 300 kpa 200degcand 28 ms and leaves at 100 kpa and 168 ms. the inlet area of

  Steam at 10 mpa and 450 degrees c enters an adiabatic

steam at 10 mpa and 450 degrees c enters an adiabatic turbine at 80 ms and exits at 10 kpa 92 quality and 50 ms. the

  With manufacturing tolerance of - 10 - 40 ohms find the

the jmh company manufactures resistors with an ideal resistance value of 400 ohms. a sample of 2000 resistors were

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd