How many watts of power would it take to heat 1 l of water

Assignment Help Civil Engineering
Reference no: EM13315426

How many watts of power would it take to heat 1 L of water(weighing 1.0 kg) by 10 degrees Celsius n 1.0 h?
Assume no heat losses occur, so all of the energy expneded goes into heating the water.

Reference no: EM13315426

Questions Cloud

How many grams of water are in the same solution : How many grams of perchloric acid, HClO4, are contained in 37.6 g of 70.5 wt% aqueous perchloric acid. How many grams of water are in the same solution.
Determine the governing load combination for both moments : A beam that is part of a rigid frame has end moments and mid-span moments for dead, live, and earthquake loads. Determine the governing load combination for both negative and positive moments at the ends and mid-span of the beam.
Calculate the total weights and values of each subset : Use the decrease-by-one technique to generate the power set and calculate the total weights and values of each subset, then find the largest value that fits into the knapsack and output that value.
Determine what is the actual length of the line for steel : A 100ft steel tape measure correctly when supported throughout its length under a tension of 1- lb and at a temperature of 72F.It is used on the field at a tension of 18 lb and supported at the two ends only.
How many watts of power would it take to heat 1 l of water : How many watts of power would it take to heat 1 L of water(weighing 1.0 kg) by 10 degrees Celsius n 1.0 h Assume no heat losses occur, so all of the energy expneded goes into heating the water.
What distance on 5 grade should be laid out with a tape : What distance on 5% grade should be laid out with a tape that measures 30.010 m under field conditions if the horizontal distance is to be 430.00m
What measurements should be laid out to establish a distance : a tape is calibrated and found to measure 100.04ft between the 0- and 100-ft marks. what measurements should be laid out to establish a horizontal distance of 682.25ft
Find the time interval between wave peaks hitting the boat : Suppose you are in a high-speed boat moving at 18.0 m/s directly into approaching 1.10 m wavelength wave. What is the time interval between wave peaks hitting the boat
What is the diameter d of the smallest-sized particles : In a hydrometer test, the data recorded at 60 minutes after the start of the test are as follows: Gs = 2.6, temperature of water T = 24°C and L = 9.2 cm. What is the diameter D of the smallest-sized particles

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the force in member ac-fh and fg

determine the force in member AC, FH, and FG and indicate if the member is in tension or compression. List all zero force members.

  Density specifications under average operating conditions

Calculate the compacted cubic yards per hour if a compactor with a 5-ft drum width travels at 3 mph over a 10-in. lift of aggregate base course with 4 passes required to meet density specifications under average operating conditions.

  Determine the heat transfer and the work for the process

A cylinder fitted with a piston has a volume of 2ft^3 and contains 0.5 lbm of steam at 60 psia. Heat is tranferred to the stream until the temperatureis 500 F, while the pressure remains constant

  What are the predominant types of bond in each category

what are the three meterials based on the predominant types of bond and what are the predominant types of bond in each category

  Determine the amount of natural alkalinity consumed

jar tests were perfomed on untreated river water. an optimum dose of 12.5 mg/L of alum was determined. determine the amount of natural alkalinity (mg/L as CaCO3) consumed.

  What are the total delay and the average delay per vehicle

Assuming D/D/1 queuing, when does the initial queue clear and what are the total delay, the average delay per vehicle, longest queue length (in vehicles), and the wait time of 100th vehicle to arrive (assumin first-in-first-out)

  What is the velocity head expressed in atmospheres

What is the velocity head expressed in atmospheres for a rapid filter operated at a surface loading rate of 475 m/d when the local porosity is 0.40?

  Determine the produce of inertia for the shaded area

Determine the produce of Inertia, Ixy, for the shaded area to the right using integration. Use the parallel axis theorem to find Ibarxy, the product of inertia with respect to the centroidal axes.

  What is bulk modulus of a liquid that has a density increase

What is the bulk modulus of a liquid that has a density increase of 0.02 percent for a pressure increase of 1000 lb/ft^2

  Determine what is the required pipe size to deliver

A concrete pipeline is installed to deliver 6m^3/sec of water (10degressC) between two reservoirs 17 km apart. If the elevation difference between the two reservoirs is 12m, what is the required pipe size

  How many trucks are required nd what is production of system

On a shovel/truck operation the production of the shovel is 293 BCY/h and a job efficiency of 0.75. The trucks used have a capacity of 12 BCY and have a cycle time of 45 min.(excluding loading).

  Estimate a value of msw generation in the year 2025

The United States Environmental Protection Agency (EPA) has published the following data for municipal solid waste generation (in millions of tons). Estimate a value of MSW generation in the year 2025.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd