How many times can he jump on his bed before beam breaks

Assignment Help Mechanical Engineering
Reference no: EM13701073

After one particularly wild night at the bars, Jon decides to come home and jump on his bed .Assume that he's jumping directly in between one steel support beam that's 10 foot long, 2 inches wide and 1 inch thick. Further assume that Jon weighs around 130 pounds and is jumping on the bed at approximately twice per second.

a. How many times can he jump on his bed before the beam breaks?

b. If there's a quarter-inch transverse crack in it already, how many times can he jump on it before the bed breaks? (Assume Paris constants of m = 4 and A = 4*10^-6 when is in MPa.

Reference no: EM13701073

Questions Cloud

What is the local heat transfer coefficient : Air at a pressure of 1 ATM, a temperature of 15° C, and a velocity of 10 m/s flows over a 3 m long flat plate that is heated to a uniform temperature of 140° C. What is the local heat transfer coefficient 3m from the leading edge of the plate?
Calculate the average temperature of the plate surface : Air at atmospheric pressure and a temperature of 25°C is in parallel flow at a velocity of 5 m/s over a 1m long flat plate that is heated with a uniform heat flux of 1250 W/m2. Assume the flow is fully turbulent over the length of the plate.
Fluid is ethylene glycol under the same flow conditions : For a laminar boundary layer flow over a flat plate with air at 20°C and 1atm, the thermal boundary layer thickness Dt is approximately 13% larger than the velocity boundary layer thickness D. Determine the ratio D/Dt if the fluid is ethylene glycol ..
Piston cylinder device contains : A piston cylinder device contains .733 kg of refrigerant-134a at -10 degrees C. The piston that is free to move has a mass of 8.63 kg and a diameter of 21.2 cm. The local atmospheric pessure is 88 kPa. Now, heat is transferred to the refridgerant-134..
How many times can he jump on his bed before beam breaks : After one particularly wild night at the bars, Jon decides to come home and jump on his bed .Assume that he's jumping directly in between one steel support beam that's 10 foot long, 2 inches wide and 1 inch thick. Further assume that Jon weighs aroun..
What is tension in swing cable developed during the motion : A gentry structure, similar to a tire swing, is used to test the response of an airplane is hoisted back until the 20m swing cable is at theta=60. Determine the speed of the plane just before crashing into the ground at theta=15, when released from r..
Determine the maximum power supplied by the engine : A sports car has a mass of 2000 kg and an engine running at an efficiency of 0.63, as it moves forward with a constant velocity of v=50 m/s,the wind creates a drag resistance on the car of FD=1.2v^ newtons. Determine the maximum power supplied by the..
Coefficient of kinetic friction between the wheels and road : A 3500 Ib. automobile is traveling down a 10 incline a 20 ft/./s. if the driver slams the break, causing the wheels to lock , determine how far the tires slide. the coefficient of kinetic friction between the wheels and the road is uk=0.5
Calculate adiabatic flame temperature butane burning : Calculate adiabatic flame temperature butane (C4H10) burning in air at 298 k and 1 atm, assuming complete combustion and constant specific heats.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd