How many gallons of water are contained in the tank if the

Assignment Help Civil Engineering
Reference no: EM13564998

1.A freeway exit ramp has a single 12-foot lane and consists entirely of a curve with a central angle of 90 degrees and L=628 feet. If the distance cleared of obstacles is 19.4 feet from the centerline, what design speed was used?

2.A spherical water tank is 10 ft in diameter. Develop a table that shows: 1) How many gallons of water are contained in the tank if the volume is measured in increments of 1 ft from the bottom to the top. 2) The mass of water at each increment, expressed in lbm.

Reference no: EM13564998

Questions Cloud

Find the magnitude and location of the resultant hydrostatic : A circular hatch is located in a sloping wall of a water-storage reservoir, where the wall slopes at ? = 35° to the horizontal, the radius of the hatch R is 840 mm, and the center of the hatch yC is 3 m below the water surface (measured along the slo..
How many inch diameter rivets are required to transmit : How many 3?4-inch diameter rivets are required to transmit 55,000 lb from the two angles to the gusset plate if the allowable shear stress in the rivets is 15,000 psi? Assume each rivet carries the same amount of load.
Determine the shear stress in the water : Would it be more efficient to use the method of section on the diagonal cross member part of the truss or do you have to use the method of joints to determine other forces first?
Determine inside volume of the pressure : A cylindrical pressure tank has internal dimensions of 14.0 inches diameter, and 36 inches length from end to end. Max. recommended pressure at 70degF is 200 PSI. The cylinder has a safety relief valve which is set at 250 PSI.
How many gallons of water are contained in the tank if the : A spherical water tank is 10 ft in diameter. Develop a table that shows: 1) How many gallons of water are contained in the tank if the volume is measured in increments of 1 ft from the bottom to the top. 2) The mass of water at each increment, expres..
What is theta max and where does it occur : A circular bar AB with ends fixed against rotation has a hole extending for half of its length (see figure). The outer diameter of the bar is d2 3.0 in. and the diameter of the hole is d1 2.4 in.
Find an estimate of the concentration of co at 6 pm if there : Find an estimate of the concentration of CO at 6 PM if there was no CO in the air at 4 PM. (Assume that CO is conservative and that there is instantaneous and complete mixing in the box)
What is the actual residence time then : The secondary clarifier actually produces 3,000 mg/l Xr, but RAS stays at 25% as originally planned. Do F/M, MLVSS and SRT change from what was planned?
Draw each of these circumstances and describe why each : Define flow at a hydraulic jump (upstream and downstream) in terms of the types of flow and corresponding Froude number. What is the depth of water at each section (upstream and downstream) compared to critical depth?

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the easiest way to solve for the 2 unknowns

Are either of the Ax or Jx forces relevant to finding the tension between H and J. If so, what is the easiest way to solve for those 2 unknowns.

  Find the velocity of sphere a and wedge b immediately

At an angle of α=30°with the vertical, a 5kg sphere is suspended on a string of length .8m with a initial velocity of 1.2m/s, it colides with wedge B. ε=.7 between the .9kg wedge and sphere A.

  Give an example of a commerical product that embodies

Prescribes that design, to be sustainable, may incorporate the integral linking of two or more components such that each component both derives and supplies benefits from and to the other

  What and where will be the maximum fluid pressure

A 10cm diameter vertical tank holds 20cm of water topped with 15cm of ethyl alcohol. The cylinder is rotated about its central axis at a rotation rate of 20 rad/s. (a) What will be the shape of the air-alcohol and alcohol-water interfaces

  Calculate the maximum tensile load in n

Consider a cold worked C11000 copper alloy rod 21 mm in diameter and 250 mm in length. Calculate (a) the maximum tensile load, in N, and (b) the maximum length, in mm, to which the rod may be stretched without plastic deformation.

  What amount will you be able to withdraw each year

At a specified point on a highway, vehicles are known to arrive according to a Poisson process. Vehicles are counted in 20-s intervals, and vehicle counts are taken in 120 of these time intervals. It is noted that no cars arrive in 18 of these 120 in..

  What is the hydraulic radius of trapezoidal channel

What is the Hydraulic Radius of Trapezoidal channel that has a bottom width of 9 feet, side slopes 3:1 (H:V) and the flow depth is 6 feet.

  Calculate the pipe diameter

A 420 kW pump delivers gasoline at a rate of 1.28 m^3/s through a horizontal pipe. The average roughness height is 0.005 cm. The total length of the pipe is 46 m. Calculate the pipe diameter.

  Find what ratio of h by b gives the minimum value of nc

Repeat LEM(Limit Equilibrium Method) analysis in clay (undrained) using a circular failure surface, with the center of the circle a distance h above the edge of the footing. What ratio of h/B gives the minimum value of Nc

  Determine the required value for m

A 1 meter diameter cylindrical mass, M, is connected to a 2 meter wide rectangular gate. The gate is to open when the water level, h, drops below 2.5 meters. Determine the required value for M. Neglect friction at the gate hinge and pulley.

  Supervisors technicians and skiled workers in dangerous work

As a project manager on site where work for 3 km long tunnel has been undertaken the site is remote and takes about 2 days to travel to nearest town supervisors technicians and skiled workers in dangerous work.

  Find los and speed within the ramp influence area and the

Find: LOS and speed within the ramp influence area and the outer freeway lanes (one-ramp is followed by off-ramp)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd