Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1)An array is defined as:ARRAY DB 2 DUP(5,2,2 DUP(4,7),6)The location of ARRAY is at 500H and DS = 0Select an instruction to read the third copy of 4.Select one:a. MOV AL,ARRAY[SI] :where SI=10b. MOV BL,[500]c. None of the answers.d. MOV [BX+SI],CL ; where BX=400H and SI=100H
2)You defined a procedure as shown below:DELAY PROC FARHow many bytes are stored on the stack by the CALL DELAY instruction?
3)Which 16 bit register holds a count for some instruction.Select one:a. None of the choices.b. BXc. AXd. EDXe. CX
4)What is the purpose of the IP/EIP/RIP register?Select one:a. Hold the address of the next instruction to be executed.b. None of the choices.c. Hold the result of computations.d. All of the choices.e. Hold the count of instructions to be executed.
A certain mixer is producing the following frequencies: 900 kHz, 700 kHz, 500 kHz, and 200 kHz. What are the two most likely input frequencies?
2) A device that responds to a small current or voltage change by activating a mechanical switch allowing a larger amount of current flow is 3) Where does a program transfer to when an interrupt occurs Interrupt vector table Interrupt service ro..
Provide a simple class definition and then provide the syntax and the rationale for declaring an array of objects of the class. Also explain the dimension of the array and why you chose that number of elements for the object array.
Determine the system fault kVA and the fault currents at the 415 V and 110 V busbars for short circuit faults on the transformer input or output terminals. Work in p.u. values of impedances.
A positron (same mass as electron) moving at .8c collides head on with a stationary electron producing two photons with EQUAL ANGLES relative to the incoming positron. Find the photon energies, wavelengths and angle
Three single phase transformers are used to form a three-phase transformer bank rated 13.8kV (delta)/120kV (wye). One side of the transformer bank is connected to a 120kV transmission line.
Define Design with Multiplexer, Design a circuit using one 16 TO 1 multiplexer with W, X,Y,Z on the control inputs
Assume the acceptable deviation is +- 5.8%. Thus, a nominal rms voltage of 120 V will range from 113 to 127 V. Suppose the line to line voltage at Customer A is 13.8kV, the load at customerA consumes complex power (1.2+j1.2)x 10^6 W.
The lithographic system A uses KrF excimer laser source (248 nm) while the lithographic system B uses the I-line of a Hg lamp (365 nm) as the photon source. Give two main shortcomings of the e-beam lithography
Voltage regulator utilizes a 500 mW Zener diode with Vz=6.7V at 20mA, rz=lOohm and IzK=5mA. The supply voltage y+ has a nominal value of 12V but can vary by ± 1 V. The load resistor is fixed at 330ohm
A set of digital scales is required to measure a load of 1000 N with an accuracy of ±1 N. Determine the minimum output resolution of the required ADC.
Build a home security system circuit using this program. The system must include a door sensor,window sensor, smoke detector, water leak sensor, a motion detector.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd