How long will it take for the pce to reach the well

Assignment Help Civil Engineering
Reference no: EM13557083

A new house is build 2000 ft from the site of an abandoned dry cleaner. 10 years ago, during the last year of operation, the dry cleaner dumped 10 gallons of tetrachloroethylene (PCE) into the aquifer. PCE has a density of 1.622 g/mL and a solubility of 0.15 g/L. the aquifer has a hydraulic conductivity of 100 gal/ft2-day, an area of 500 ft2, a porosity of 0.35 and a hydraulic gradient of 0.008

a. The PF of PCE is 0.051 (mg/kg-day)^-1. Calculate the MCL for the acceptable risk of 1/10^6 

b. How long will it take for the PCE to reach the well at the new house 

c. The water is pumped out of the aquifer at a rate of 2000 gpd, treat it with activated carbon and then put it back into the aquifer. At the flow rate how long until al the PCE is removed, assume carbon removed 100% of the PCE

Reference no: EM13557083

Questions Cloud

Estimate the standard deviation of the population : A sample of 10 television tubes produced by a company showed a mean lifetime of 1200 hours and a standard deviation of 100 hours. Estimate
Constuct a choice table for interest rate from 0% to 100% : The owner of a downtown parking lot has employed a civil engineering consulting frim to advise him on the economic feasibility of constructing an office building on the site. bill samuels, a newly hired civil engineer, has been assigned to make the a..
What maximum force can this person apply with this jack : A container of petrol on a set of scales is used to measure the rate at which fuel is used by an engine under test. In one test the weight measured by the scales decreases by 25.0 N in 1 hour. (Assume the specific gravity of petrol is 0.720 and g is ..
What is its speed at the point that the force resisting : This problem models an insertion process. Block A (mA = 2kg) is acted on by a horizontal force F (F = 12 N). As A moves to the right, it gets pressed more and more tightly in the channel.
How long will it take for the pce to reach the well : The water is pumped out of the aquifer at a rate of 2000 gpd, treat it with activated carbon and then put it back into the aquifer. At the flow rate how long until al the PCE is removed, assume carbon removed 100% of the PCE (ans. 54 days)
How long will it take the water in the aquifer to travel : A truck spils 1 gallon of benzene into an aquifer with an area= 50ft^2 Benzene has a solubility of 1750 ppm, and a specific gravity of 0.873. The aquifer ahs a porosity of 0.25, a hydraulic gradient of 0.004 and a hydraulic conductivity of 1000 gpd/f..
Determine the speed of the arrow after traveling from rest : A bowstring produces a force against a 2.0 oz arrow given by where a = 40 lbf, b = 3.2 ft-1 and x is in ft. x = 0 when the arrow is pulled fully back and increases as the arrow moves forward. Determine the speed of the arrow after traveling from rest..
Calculate the power rating of the electric heater required : A room 7m x 6m x 3m high is to be electically heated to maintain the inside temperature at 20 C, when it is 0 C outside. The room has 2 windows each 1.2m x 1.8m and a sliding glass door 2.4m x 2.1m. The transmission coefficients u in Wm^2/C are given..
What input of power rating is required for the pump : A water storage tank located on a larege dairy farm has a storage capacity of 0.1 ML. The average rate of water consumption from this tank is 6.25 kL per day, every day.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the maximum deflection of the beam

A hardwood beam of rectangular cross-section 150x300 is simply supported over a span of 8m, and is loaded as sketched. Determine the maximum deflection of the beam. (Youngs modulus E = 12 x 10^3 MPa)

  What are the bearings of the sides

Why is the torque on A and the torque on AB opposite? Wouldn't they be the same? How do we know which direction the torque is applied at A to begin with? It's not specified.

  Determine te maximum normal stress in the container

A spherical gas container made of steel has a 5-m outer diameter and a wall thickness of 6 mm. Knowing the internal pressure is 350 kPa, determine te maximum normal stress and the maximum shearing stress in the container.

  How the strains deform the element within the x-y plane

Use the strain-transformation equations to determine (a) the in-plane principle strains and (b) the maximum in-plane shear strain and average normal strain.

  What size pipe should we use to obtain a flow

Two large water reservoirs are connected by 8,000 ft of schedule 40 steel pipe. The level of one reservoir is 500 ft above the level of the other

  What is the demand for time if left turns are provided

Given the following geometry of an intersection: Four lanes fornorth and southbound traffic; two lanes for east and west boundtraffic. The peak hour volume for

  How to compute the saturated unit weight of the silt

All the silt is saturated even after the water table is lowered. (In this problem, treat the unit weight above the water table as bulk unit weight and the unit weight below the water table as saturated unit weight.)

  Magnitudes of fac and fad

The 70 m tall tower is supported by three cables that exert forces FAB, FAC, and FAD on it. The magnitude of the force FAB is 2 kN. The x and z components of the vector sum of the forces exerted on the tower by the three cables are zero. What are ..

  Write a paragraph explaining how the relaxation modulus

Write a paragraph explaining how the relaxation modulus of a plastic material measured in engineering practice. use a sketch.

  What is the lowest maximum cycle temperature at the engine

the pressure ratio across the compressor is 9 and the maximum temperature is 827c.the turbine and comprssor processes are adiabatic with turbine efficiency of 90% and a compressor efficiency of 85%.

  Find the flow rate and the pressure head at the base of

An 8-in-diameter pipeline (f=0.028) 500 ft long discharges a 3-in-diameter water jet into the atmosphere at a point that is 250 ft below the water surface at intake.

  Compute the after-tax rate of return on the vessel

At the end of the 6 years, the oil company exercised its option and bought the vessel. The chemical company has a 34% incremental tax rate. Compute its after-tax rate of return on the vessel.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd