How long will it take for half of the water to drain out

Assignment Help Mechanical Engineering
Reference no: EM13708230

An open cylindrical tank that is 2 ft in diameter and 4 ft high is full of water. If the tank has a 2 in diameter hole in the bottom, how long will it take for half of the water to drain out, if friction is neglected?

Reference no: EM13708230

Questions Cloud

Coaching model : "Coaching Model"   acronym, create your own coaching model, and define the meaning of each letter as it relates to performance management. Specify the primary reasons that you believe your model would be effective. Justify your response.
Develop a preliminary design : Develop a preliminary design, including flow rates, pipe sizes, and pipe slopes for a trunk sewer to be laid in the development shown in the accompanying figure from 6th to 1st Streets along Peavy Avenue
Calculate the pressure at the nozzle exit : Moist air at 35 degree C, 3 bar, and relative humidity 30% (State 1) enters a nozzle with a velocity of 50 m/s and expands in a reversible and adiabatic process such that the moist air leaving the nozzle is about to condense (State 2). Calculate the ..
Calculate the mass flow rate of moist air : A non-reacting gaseous mixture with molar analysis of 74.3% N2, 4.3% O2, 7.1% CO2, and 14.3% H2O(g) enters a counter-flow heat exchanger at 800?F and 1 atm with a volumetric flow rate of 5 ft3/s (State 1) and exits at 200?F (State 2). Calculate the m..
How long will it take for half of the water to drain out : An open cylindrical tank that is 2 ft in diameter and 4 ft high is full of water. If the tank has a 2 in diameter hole in the bottom, how long will it take for half of the water to drain out, if friction is neglected?
Electronic components of computer are cooled by air flowing : The electronic components of a computer are cooled by air flowing through a fan mounted at the inlet of the electronic enclosure. At steady state, air enters at 18oC, 1 atm. For noise control, the velocity of the entering air cannot exceed 0.9 m/s. F..
Determine the velocity of the water at the inlet and exit : A pump is employed to deliver liquid water from a pond to a higher elevation. The pump steadily draws water from the pond at a volumetric flow rate of 192 gal/min through a pipe having a 7 in diameter inlet. The exit diameter of the pipe is 2 in. and..
Show the specs of bearers and joists : You need to park a car under it so there can be no supports in the middle. Attached to the wall on one side and steel post on the other.
Determine the volumetric flow rates at the inlet : Refrigerant 22 enters an insulated compressor operating at steady state as saturated vapor at -16oC with a mass flow rate of 1.5 kg/s. Refrigerant exits at 7 bar, 70oC. Changes in KE and PE from inlet to exit can be ignored.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd