How long until the concentration is reduced

Assignment Help Civil Engineering
Reference no: EM13561468

The Fluoride feeder runs out of feed solution. The rapid mix tank is connected to a 5 km long distribution pipe. The flow rate into the tank mix tank is 0.44 m?/s and the volume of the tank is 2.50 m?. The velocity of the distribution pipe is 0.17m/s. If the Fluoride concentration in the tank is 1.0 mg/L when the feed stops how long until the concentration is reduced to 0.1 mg/L at the end of the distribution pipe? The fluoride may be considered non-reactive.

Reference no: EM13561468

Questions Cloud

Discuss the signals and systems as they exist in these : A square footing 0.3 m by 0.3 m is placed on the surface of a dense cohesionless sand (unit weight = 18.2 KN/m^3) and subjected to a load test. If the footing fails at a load of 13.8 KN, what is the value of ? (degree) for the sand?
Calculate the screen drag force : A variable mesh screen produces a linear and axisymmetric velocity profile as indicated below in the air flow through a 2-ft diameter circular cross section duct.
Determine the secondary sludge produced per day per pound : A low rate trickling filter plant gives 95% BOD5 removal. the primary clarifier removes 33% of the BOD5 applied to it. the secondary sludge amounts to 0.029lb dry solid/cap-day. if the raw wastewater has a BOD5 of 0.17lb/cap-day.
Determine the volume of stone required for each filter : A two stage high rate trickling plant is to treat a municipal wastewater having a flow of 2.0mgd. pertinent data: influent BOD5 = 200mg/l, BOD5 removal by primary clarifier = 33%, filter bed depth = 5 to 7ft,
How long until the concentration is reduced : The Fluoride feeder runs out of feed solution. The rapid mix tank is connected to a 5 km long distribution pipe. The flow rate into the tank mix tank is 0.44 m?/s and the volume of the tank is 2.50 m?.
Determine the force supported by the hydraulic cylinder : A Steel plate weighing 205 lb with a center of gravity at point G is supported by a roller at point A,a bar DE, and a horizizontal hydraulic cylinder BC. Negelcting all weights of all members except for the plate,
What is the maximum acceleration from rest of the car : A car has a 10-ft wheelbase (L). the center of gravity is 18 inches about the ground and 5 ft behind the front axle. The weight of the car is 2500 lb. mechanical efficiency if the drivetrain is 85%. and the wheel radius is 15 inches
What is the rolling resistance of the road : A CAT 834H (rubber tires, high pressure), with an operating weight of 103,849 lbs, is pulled up a road whose slope is +3.0% at a uniform speed. If the average tension in the towing cable is 6,060 lb,
How much does the choice of the distribution affect : On a single graph, plot the PDFs if E is assumed to be normally, lognormally, and gamma distributed.  Plot the PDFs for E values between 10,000 and 50,000 kips/in2.  Make sure to label the axes and use a legend to label the curves.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find tensile stress that will give probability of failure

The median value of the rupture strength was 300 MPa. The ceramic is to be used for components with dimensions l=50mm, b=d=5mm loaded in simple tension along their length. Calculate the tensile stress that will give a probability of failure of the..

  A cm reactor receives influent containing 100 mgl of tracer

a cm reactor receives influent containing 10.0 mgl of tracer for 2 h. then tracer addition is terminated but the flow

  What is the friction force under block b when this occurs

Two blocks A and B have a weight of 10 and 5 , respectively. They are resting on the incline for which the coefficients of static friction are = 0.15 and = 0.40. The spring has a stiffness of = 7 and is originally unstretched.

  Find magnitude of the total acceleration of roller coaster

the roller coaster track consists of a circle in a vertical plane of radius 150m. find the magnitude of the total acceleration of the roller coaster if, at the time shown, the car is moving at 50 km/hr and is gaining speed at the rate of 0.4g

  Calculate the carbon content required at surface of steel

A 0.02wt% C steel is to be carburized at 1200°C in 4 hrs with a point 0.6mm beneath the surface reaching 0.45wt%C. calculate the carbon content required at the surface of the steel.

  Determine by trigonometry the corresponding magnitude of r

Knowing that the magnitude of P is 35 N, determine by trigonometry (a) the required angle a if the resultant R of the two forces applied to the support is to be horizontal, (b) the corresponding magnitude of R.

  Determine acceleration of rod and reaction at a and b

The motion of the 2.5-kg rod AB is guided by two small wheels which roll freely in horizontal slots. If a force P of magnitude 8 N is applied at B, determine (a) the acceleration of the rod, (b) the reaction at A and B.

  Determine the critical depth and critical velocity for flow

A trapezoidal channel has a bed width of 3.5 m and a side slope of 30 degrees from the horizontal. Determine the critical depth and the critical velocity for a flow of 22 cubic meters per second.

  Calculating coefficient of permeability

The temperature was 200C, and the void ratio (e) of the soil was 0.43. Calculate the "Coefficient of Permeability" in "centimeters per second" (Given, k = (QL)÷(A Δh t)).

  What was the students associated perception reaction time

The student strikes the sign at a speed of 25 mi/h. if the student was travelling at 65 mi/h when the sign was first spotted, what was the student's associated perception reaction time

  Determine number of bolts necessary to make max shear stress

Assuming that the shear stress in the bolts is uniform, determine the number of bolts necessary to make the maximum shear stress in the shaft equal to the shear stress in the bolts. Each bolt has a diameter d.

  Use the doubling time approximation to estimate

Use the doubling time approximation (3.5) to estimate the exponential rate of growth that would produce those numbers. Use the exponential growth equation (3.6) to find the growth rate

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd