How long must radioisotope be held to meet allowable charge

Assignment Help Civil Engineering
Reference no: EM13306445

A hospital waste containing 0.7µCi/L of 32P is to be disposed of. How long must the radioisotope be held to meet the allowable discharge activity?

Reference no: EM13306445

Questions Cloud

What is the value of the torque applied : A wheel has a rotational moment of inertia I=150. It is accelerated by a constant torque from rest to a final angular velocity of 1.0. what is the value of the torque applied
Calculate bending stress distribution which present at base : Assume the beam is 2" x 10" in cross section. Calculate the bending stress distribution that is present at the base of the cantilever and at every 2.5 ft increment toward the free end of the beam
Find the average translational kinetic energy of a molecule : Two moles of an ideal gas are placed in a container whose volume is 6.2 x 10-3 m3. find the average translational kinetic energy of a molecule
Determine the mass flow rate of blood : Calculate the mass flow rate (in grams per second) of blood (Ï = 1.0 g/cm3) in an aorta with a cross-sectional area of 2.0 cm2 if the flow speed is 47 cm/s
How long must radioisotope be held to meet allowable charge : A hospital waste containing 0.7µCi/L of 32P is to be disposed of. How long must the radioisotope be held to meet the allowable discharge activity
What is the steady state amplitude of the vertical response : Consider just the vertical (y) response of the system when the beam is being stretched. Show that the spring constant, ka, is approximately 70.6 mN/m. What is the steady state amplitude of the vertical response? See Figure A below for an engine..
Calculate the turning moment required to operate the gate : A pipe line of 1.25 m diameter has a circular gate at its end. This gate can be operated around its horizontal diameter. If the pipe is flowing full with velocity almost equal to zero, calculate the turning moment required to operate the gate
Sketch scs triangular and curvilinear uhs and mass curve : Sketch the SCS triangular and curvilinear UHs and the mass curve for a 100-mi^2 watershed which is 60% good condition meadow and 40% good cover forest land. The watershed consists of 70% soil group C and 30% soul group A.
Determine the horizontal distance that the tile will travel : A tiler is removing broken tiles from the roof of a house, and throws a tile with a velocity of 8 m/s at an angle of 20 degrees above horizontal. At the point of release the tile is 5.2 m above the ground surface.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the ieee double precision floating number

Calculate the IEEE double precision floating number immediately greater than the minimum number in double precision in both binary and decimal form

  Length of contracted rectangular weir

A trapezoidal canal 6m wide at the bottom and having a side slope of 1V:2H carries water with a mean velocity of 1.0m/s to a depth of 60cm. What length of contracted rectangular weir 1.0m high should be placed at the middle of the canal to make th..

  Create a primary function

create a primary function that uses a function handle with a nested function to compute the ninimum of the function 20x^2-200x+12 over the range 0

  Determine the change in the bar thickness of axial load

At an axial load of 23 kN, a 40-mm-wide by 10-mm-thick polyimide polymer bar elongates 2.7 mm while the bar width contracts 0.17 mm. The bar is 240 mm long. At the 23-kN load, the stress in the polymer bar is less than its proportional limit.

  Calculate carbonate-noncarbonate and total hardness

Calculate carbonate, noncarbonate, and total hardness Na+ = 27.8 mg/L Cl- = 35.6 mg/L Ca+2 = 48mg/L CO3-2 = 30 mg/L Mg+2 = 12mg/L HCO3- = 61 mg/L K+ = 12 mg/L SO4-2 = 48 mg/L

  Describe the ductility of a reinforced concrete beam

What does under-reinforced mean Which is desirable and why How would your Moment-Curvature plot be affected if the amount of tension steel was doubled How would your Moment-Curvature plot from part a be affected if compression steel was added to the..

  Determine smallest values of c and k for static deflection

the turbopump unit in the engine nominally operates at 7000 rpm, and a result of design issue, the actual thrust provided by the engine oscillates harmonically with an amplitude of 10 KN at the same rotational frequency as the turbopump unit.

  Determine what is the pressure in cell that can be varied

Pure n-butane is contained in a laboratory cell in which the volume can be varied. The cell is maintained at a temperature of 200°F. The volume is changed until a few drops of liquid n-butane are present. What is the pressure in the cell

  Determine what is the height of the pure water column

a closed tank contains two straified non misicble fluid layers and compressed air. the fluid of the tank is saline water (relative density 1.036) with a total depth of 3.5m. the top fluid layer is oil (relative density of 08.2) with a depth of 0.6..

  What is elevation of b by neglecting curvature and reaction

The line of sight of a level falls at a rate if 0.122ft/ 100 ft when the level bubble is centered. A backsight of 4.782 is taken on point A, which is at 75 ft from the level. the elevation of a is 425.238 ft.

  What is the equivalent pressure drop in standard atmospheres

A HEPA (high efficiency particulate air) filter is monitored periodically for replacement. Specifications state that if the pressure drop across the filter exceeds 1 inch of water, the filter should be replaced.

  Determine the magnitude and direction of the components

The beam is subjected to a force F=825 lb in the direction, and is supported by a pin connection at point B and a rope attached through a pin connection at point A. Problem #1: Draw a complete FBD of the beam.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd