How long must diameter be for mallet to balance at a point 6

Assignment Help Civil Engineering
Reference no: EM13322181

A wood mallet has a cylindrical head 6 inches long and 3 inches in diameter. If the cylindrical head is 1 inch in diameter how long must it be for the mallet to balance at a point 6 inches from where the handle enters the mallet? (use 40 lb / ft cubed) for wieght of wood.

Reference no: EM13322181

Questions Cloud

What mass should be placed on the second cylinder : A cylinder of radius 25 cm is filled with an ideal fluid, If the height of the two cylinders is exactly the same, what mass should be placed on the second cylinder to balanced the system
What points along the line of action of the force f : What points along the line of action of the force F_evec would simplify the calculation of M, the magnitude of the total moment due to the force F_evec about point O
What is the absolute pressure at the bottom of the lake : A lake is 28.3 meters deep at its deepest point. The density of water in the lake is 1000 kg/m^3. what is the absolute pressure at the bottom of the lake
What is the resonance angular frequency of this circuit : A parallel-plate capacitor having square plates 4.50cmcm on each side and 8.00mmmm apart is placed in series with an ac source of angular frequency 650radrad/s, What is the resonance angular frequency of this circuit
How long must diameter be for mallet to balance at a point 6 : A wood mallet has a cylindrical head 6 inches long and 3 inches in diameter. If the cylindrical head is 1 inch in diameter how long must it be for the mallet to balance at a point 6 inches from where the handle enters the mallet
Meeting regulatory or legislative standards-guidelines-goals : How do you deal with limited resources when you are responsible for providing quality care and meeting regulatory or legislative standards/guidelines/goals?
Determine the average power delivered by the source : An L-R-C series circuit has 97.5%u03A9 , and the amplitude of the voltage across the resistor is 30.0VV . What is the average power delivered by the source
What is the buoyant force acting upon the styrofoam block : A cube with side length 1.53m of solid Styrofoam is completely submerged in fresh water such that the top of the Styrofoam block, what is the buoyant force acting upon the Styrofoam block
Draw the influence line for the shear at point b : Draw the influence line for the shear at point B. Plot numerical values every 5 ft. Assume the support at A is a roller and C is fixed. EI is constant.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Develop a way to reforest the region by preventing wildllife

A fire has destroyed thousands of acres of forest. Seedlings have been planted in the area but are being destroyed by the local wildlife. Develop a way to reforest the region by preventing the wildlife from eating the seedlings

  Determine the maximum allowable value of p

The compound bar carries the axial forces P and 2P. Find the maximum allowable value of P if the working stresses are 40 ksi for steel and 20 ksi for aluminum, and the total elongation of the bar is not to exceed 0.2 in.

  Plot the variation with depth

Plot the variation with depth (z) of the at-rest lateral earth pressure behind the wall, and determine the magnitude and location of the at-rest lateral earth force per unit length of wall.

  Determine the required area of the members

The truss is to be constructed of members with equal cross-sectional areas and using a material with yield stress 700 MPa. The structure must be designed to support a mass (m) of 3400 kg with a factor of safety of 3.

  Calculate the maximum acceleration bungee experiences

A 55 KG bungee jumper leaps from a bridge. She is tied to a bungee cord that is 12 m long when unstretched, and falls a total of 31 m. Calculate the spring constant of the bungee cord assuming Hooke's law applies.

  Determine largest positive value p the structure can support

The structure consists of two uniform members AB and BC, each weight 2kN. The member are pinned to each other at B, and the structure is supported by a pin at C and a surface at A having coefficient of static friction 1.2.

  What is the probability that if purchased car is better

An automobile that you are looking at purchasing has an advertised fuel mileage of 30 miles per gallon. You rent the car for a week and track your mileage to school and back home and get (miles/gallon)

  Calculate the flow rate through the pipe and the force

A thin-walled pipe, of diameter 4 in., is held stationary in a river flowing at 6 ft/s parallel to its axis. The pipe contains a sharp-edged orifice, of diameter 3 in., with a contraction coefficient of 0.60 based on the area.

  How does the result differ from the case of oblique impact

In the Civil War there were numerous incidents in which the bullet fired from a Union soldier's rifle struck and fused with the bullet from a Confederate's rifle. Assume the impact scenario.

  Determine what is the final weight in pounds and newtons

A container weights 2.06lb. It is filled with 1.09ft^3 of water at 25 degrees Cel. What is the final weight in pounds and newtons

  Find expressions for substantial time derivative components

A steady-state, incompressible two-dimensional velocity field (u,v) is given by the following components in the xy-plane u = 0.2 + 1.3x + 0.85y v = -0.5 + 0.95x - 1.3y

  How many iron atoms are contained in the paper clip

A typical paper clip weighs 0.59 gram and consists of BCC Iron. The density of iron is 7.87 gram/cm3 and its atomic radius is 0.124 nm. What is the volume of a unit cell in (nm)3. What is the volume of a unit cell in cm3.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd