How long in seconds would it take to discharge the capacitor

Assignment Help Electrical Engineering
Reference no: EM13261673

A 2 farad capacitor is charged up to 400v by a dc power supply. How long in seconds would it take to discharge the capacitor to a safe stored energy level of 1 joule using a 1k ohm high wattage resistor bank.

Reference no: EM13261673

Questions Cloud

How to calculate the standard cell potential : Use the standard half-cell potentials listed below to calculate the standard cell potential for the following reaction occurring in an electrochemical cell at 25°C.
Design stable optical cavity using one mirror with radius : design a stable optical cavity using one mirror with infinite radius of curvature and 95% reflectivity. We want the cavity to 1 m long. Assume the second mirror is 100% reflective. a. Design the cavity such that g1g2 product is 0.5
Brief review to the idea of research design : Respond and give a brief review to the idea of Research Design. Think as a good idea of research design and write about why you think it is a good idea for research design.
Compute the mass of li formed by electrolysis of molten : Calculate the mass of Li formed by electrolysis of molten LiCl by a current of 6.9×104 A flowing for a period of 23h . Assume the electrolytic cell is 80% efficient.
How long in seconds would it take to discharge the capacitor : A 2 farad capacitor is charged up to 400v by a dc power supply. How long in seconds would it take to discharge the capacitor to a safe stored energy level of 1 joule using a 1k ohm high wattage resistor bank.
Carbon monoxide as well chlorine combine in an equilibrium : Carbon monoxide and chlorine combine in an equilibrium reation to produce the highly toxic product phosgene. CO + Cl2 COCl2. If the equilibrium constant for the reaction Kc = 248
Determine the expression for the frequency response h : Determine the expression for the frequency response H(O) of a causal IIR LTI discrete-time system characterized by the input-output relation y[n]=x[n]-ay[n-R], |a|
Estimate the radius of curvature of the mirror : You are standing 4.5m from a convex security mirror in a store. You estimate the height of your image to be half of your actual height. Estimate the radius of curvature of the mirror
What are the bus protocols that support plug and play device : 1- what is meant by plug and ply devices what are the bus protocols that support plug and play devices 2- what is hot attachment and detachment what are the bus protocols that support hot attachment and detachment

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the snr needed for bpsk from the error rate curves

Suppose the FCC allocates 300 kHz channels for a high quality video conference service. A service provider decides that this service requires 720 kbps (not including overhead and error control) for each channel.

  Determine what is the channel bandwidth

A binary waveform of 53000 bits/sec is converted into an 8192 level waveform that is passed through a channel with a raised cosine-rolloff filter characteristic with r = 0.33. The channel bandwidth is what

  Write down all of the frequency components

Four frequencies are applied at the input of a non-linear amplifier. Write down all of the frequency components at the output of the non-linear device. Write down only the first three harmonics.

  Determine an equation for angular velocity

If the battery is replaced with a 6 Volt battery it was experimentally determine that the no load speed is reduced to 120 rpm. For this situation, determine a new equation for angular velocity,(in rad/sec) versus Torque (in Nm).

  How many ip packet will be required to transport entire song

Given that you want to transfer a 3MB song by sending packets across an Ethernet link that has a MTU. of 1500 Bytes, answer the following questions. (for this question use 1MB = 1024KB, 1KB=1024Bytes)

  What is the minimum number of bits required

What is the minimum number of bits required to represent each of the following decimal numbers: 10, 1000, 100,000, and 1,000,000?

  Calculate length of time it takes for a signal to pass down

1. Calculate the length of time it takes for a signal to pass down an Ethernet bus that is 300 m in length, assuming the velocity factor of the cable is 0.66. 2. For the Ethernet bus in problem 1 and a communication rate of 10 Mb/s

  Determine what is the order of the given system

c) Find the output y(t) in response to the input x(t) = 6 u(t), where u(t) is the unit step function. d) Find the output y(t) in response to the input x(t) = δ(t) A linear system has the system response function H(s)= -7/(s+4)

  Determine whether the given signals are periodic

Determine whether the following signals are periodic. If they are, find the smallest periods (fundamental periods). a) f(x,y) = sin (2 pi x) cos(4 pi y) b) Discrete signal: f(m,n) = sin ( pi * m / 5) cos(pi * n / 5)

  What is the phase angle of the impedance of an inductor

1- What is the magnitude of the impedance of an inductor of 34 H at an angular frequency of 783 rad/s (0 decimals in k) 2- What is the phase angle of the impedance of an inductor of 87 H

  Define magnetic material allocated to each bit information

A 3.5inch floppy disc has a nominal capacity of 2 MB. Note that there are eight bits to a byte. Estimate the area of magnetic material allocated to each bit of information. Clearly state any assumption made and carefully note any measured quantiti..

  Which of frequencies represents the pre-warped frequencies

design an IIR high-pass filter using bilinear method in a system with sampling frequency of 100 Hz. The lower and higher cutoff frequencies are at 18 Hz and 35 Hz respectively. Pre-warp the cutoff frequencies.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd