Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A boron diffusion into a 1 -ohm-cm n type wafer results in a Gaussian profile with a surface concentration of 5 x 10^18/cm^3 and a junction depth of 4um.a)how long did the diffusion take if the diffusion temperature was 1100 degrees C?b)what was the sheet resistance of the layer?c)what is the dose in the layer?
A tidal energy system has an average tidal range of 5 m and a basin area of 21.5km^2. The system is designed to generate power during both incoming and outgoing tides. The seawater density 1025kg/m^3, and the tidal period is about 12.5 hours.
Assume one LED (LED1) and one switch input (SW1). Write a while(1) { } loop that initally will blink an LED1 once power is applied. On each press OR release of SW1, alternate between terminating blinking and resumingine the blinking. Draw a state ..
Design a DC current source to meet the following specifications: - Current source value: 100 u-amps +/- 1% (over all possible load and supply voltage conditions). - Output resistance: >20 Mohms. - Available DC voltage sources are bipolar and range fr..
A touch sensor base on a piezoresistor built into a micromechanical cantilever made of silicon is cnnected in a Wheatstone-bridge configureation with a Vo = 1 volt. If L = 1.44cm and W = 1 cm
The following represent solutions of the transmission line differential equations for some arbitrary function f(u): V(z,t) = 60 cos(1000t -5z) - 120 pi f (2t + z/100+12) V I(z,t) = 2 pi f (2t +z/100 +12) - cos (1000 t -5z) A a) what is the forward pr..
Connect a voltage divider to an output of a DC power supply. Design it to give an output that is 1/3 of the supply voltage. Furthermore, neither the power ratings of the resistors nor the current rating of the supply are to be exceeded.
Find the sketch the convolution of the given pairs of functions. You can use either the integration or the graphical method for convolution. x(t) = 2e-3t sin(2t) u(t) h(t) = u(t) + 4d(t-2) find y(t) = x(t) * h(t)
A three-phase, 400 V system has the following load connected in delta: between the red and yellow lines, a non-reactive resistor of 100; between the yellow and blue lines, a coil having a reactance of 60 and negligible resistance
In a particular technology, a small BJT operating at vBE = 28VT conducts a collector current of 100µA. What is the corresponding saturation current. For a transistor in the same technology but with an emitter junction that is 32 times larger
the capacitance varies depends on the distance of the two plates from 0 to about 20in. this model is needed to generate an input to an other part of the circuit to simulate it and obtain the output in PSPICE.
a) The input of Hex- to - seven segment decoder is 1010. what will the display show b) A priority encoder has all inputs activated. Which input will be encoded. Why c) how many select input lines are needed for a 128- to - 1 multiplexer
f(t) = A[u(t) + u(-t/2-5)-1], where u(t) is the unit step function. Is the energy of this signal finite? Why or why not. If it exists, find the energy of this si
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd