How high did the ball roll before it momentarily stopped

Assignment Help Civil Engineering
Reference no: EM13317913

A solid ball starts to roll up a hill with an initial velocity of 50m/s. The ball has a mass of 20 Kg with a 0.75 m radius. How high did the ball roll before it momentarily stopped?

Reference no: EM13317913

Questions Cloud

Where to locate the mass center of the assembly : The two upper lengths of the welded Y-shaped assembly of uniform slender rods have a mass per unit length of 0.3 kg/m, while the lower length has a mass of 0.7 kg/m. Locate the mass center of the assembly. lenghts of all rods aew 30mm
What is the maximum weight that can be suspended on poll : What is the maximum weight that can be suspended on a 16 Kg poll, 3/5 from the end. The maximum tension of the 30 degree guy-wire is 1500 N. Find the horizontal and vertical forces exerted on the poll by the hinge.
What is min required heat transfer rate from heat source : A waste heat source is available at 400°C. A heat engine operates using heat from this source. It rejects heat to the surroundings at 38°C. The power from the engine runs an air conditioner to keep the air inside a building at 25°C
Find temperature at which air must leave heat exchanger : Gaseous oxygen (99% pure, molar basis) is to be produced at a rate of 350ft^3/hr in a Linde single column plant. The column operates at a pressure of 1 atm. Air leaves the compressor at a pressure of 10 atm.
How high did the ball roll before it momentarily stopped : A solid ball starts to roll up a hill with an initial velocity of 50m/s. The ball has a mass of 20 Kg with a 0.75 m radius. How high did the ball roll before it momentarily stopped
How far did the person climb on a frictionless vertical wall : A uniform ladder with a mass of 15 kg is placed on a frictionless vertical wall. An 80 kg person climbs up the ladder. If the coefficient of friction between the floor and the base of the ladder is 0.15, how far did the person climb
Find what concentration would correspond to a risk : The drinking water standard for tetrachloroethylene is 0.005 mg/L. Using EPA exposure factors for residential consumption, what lifetime risk would this pose What concentration would correspond to a risk of 10-6
Determine the mass of the second car : A 9200 kg boxcar traveling at 15.8 m/s strikes a second boxcar moving at 7.11 m/s in the same direction. What is the mass of the second car
How many gallons would be required to last same time as gas : A water treatment plant effluent is to be disinfected with chlorine from ton cylinders of compressed gas. The plant is 5 million gallons per day. There are a total of 10 useable cylinders in the plant.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what force is required to hold the shield in place

Water at 70oC (row = 1.94 slugs/ft3) flows out of a nozzle (diam. = 1in) with a velocity of 10 ft/s at an individual holding a protective shield. If the water deflects off of the shield perpendicular to the original stream in all directions

  Explain how to estimate the et losses for the area in 1 year

It the mean annual runoff of a drainage basin of 10000 km^2 is 140 m^3/s, and the average annual precipitation is 105 cm, estimate the ET losses for the area in 1 year. What are your assumptions

  How many cubic yards of soil must be excavated from pit

The soil will be excavated from the borrow pit, moistened to increase the water content to 13.5% (assume i will not change the volume of solid mass) and then compacted to a final dry unit weight of 118 pcf.

  Determine the molar specific volume of the air

Atmospheric air is at 101 kPa (abs) and 25 degrees C. Determine (a) the density of the air (b) the molar specific volume of the air. Work out problem completely please. I already have the answers a) 1.18 kg/m^3 b) 24.5 m^3/kmol

  Determine reaction components that ball exert on rod abc

The smooth surface that provides the support at C lies in the y-z plane. Determine the reaction components that the ball and socket exert on rod ABC, the tension in cable BD, and force the smooth wall exerts on end C of rod ABC.

  Calculate what is the force required at a constant rate

A 20-kg iron ball is moving at 100 km/hr should be accelerated at a constant rate of 10 m/(sec)^2. What is the force required

  What is the magnitude and direction of specific discharge

Groundwater moves through a sandstone porous media and is driven by a gradient of -0.05 directed at an angle of 60 degree counterclockwise from the x-axis.

  Determine the distance d between a and b

the force-couple system at A is to be replaced by a single equivalent force acting at a point B on the vertical edge of the triangular plane. determine the distance d between A and B

  Determine the design a typical joint 50mm wide

A floor is to be supported on hardwood timber joists that are spaced at 0.5m centres and span 5.0m. The joists support flooring 20mm thick and an applied live load of 2kN/m2 Design a typical joint 50mm wide

  Calculate what is the pressure at the siphon crown

The siphon crown is 1.2m above the water surface elevation of the reservoir and a length 10m away from the siphon entrance. If the siphon diameter is 30 cm, if the friction factor is .02, and the headless coefficient are .2 (inlet) and 1 (exit),

  How many kg per day of naoh must be added to neutralize

How many kg/day of NaOH must be added to neutralize a waste stream generated by an industry producing 90.8 million g/day of sulfuric acid, if 0.1% of the sulfuric acid produced is lost to wastewater The wastewater flow is 750,000 L/day

  Determine the force in member ac-fh and fg

determine the force in member AC, FH, and FG and indicate if the member is in tension or compression. List all zero force members.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd