How high above the ground is the balloon at the instant the

Assignment Help Mechanical Engineering
Reference no: EM13623618

The position of an object is moving along an x axis is given by \(x=3t - 4t^{2}+t^{3}\) where x is in meters and t is in seconds.

1) Find the position of object when t=0,4

2) What is the displacement between t=0 and t=4s

3) What is the average velocity for the time interval from t=0 to t=4s

4) What is the instantaneous veloxity at t=4s

5) Is this object moving with constant acceleration

6) At what time is the object's velocity 0

A hot air balloon is descending at the rate of 12m/s and is 80m above the ground when a package is dropped over the side. assume that the balloon continues to descend at a constant speed of 12m/s

1) How long does the package take to reach the ground?

2) With what speed does it hit the ground?

3) How high above the ground is the balloon at the instant the package hits the ground?

4) How long after the package hits the ground does the balloon reach the ground?

Reference no: EM13623618

Questions Cloud

A 4 microf capacitor is charged by a 200 v supply it is : a 4 microf capacitor is charged by a 200 v supply. it is then disconnected from the supply and is connected to another
The water in the pool is 25 feet deep and the rim of the : a garden hose is open at one end and capped closed at the other. a swimmer in an above-ground pool fills the hose with
View this energy as stored in the electrostatic field : the plates of a parallel plate capacitor have an area of 90 cm2 each and are separated by 2.5 mm. the capacitor is
What is the area of the plates of a 2 f parallel plate : what is the area of the plates of a 2 f parallel plate capacitor given that the separation between the plates is 0.5
How high above the ground is the balloon at the instant the : the position of an object is moving along an x axis is given by x3t - 4t2t3 where x is in meters and t is in
As the chain is raised assuming that the motor supplies a : a ships anchor chain is wrapped around a hollow steel drum of mass m 500 kg and radius r 0.5m. the drum is located on
The water in the pool is 25 feet deep and the rim of the : a garden hose is open at one end and capped closed at the other. a swimmer in an above-ground pool fills the hose
If at a given instant r 71 miles and theta 34 degrees : a radar station is tracking a plane flying at constant altitude with a speed of v0 600 mph. if at a given instant r
A large number of 1 microf capacitors are available to him : an electrical technician requires a capacitance of 2 microf in a circuit across a potential difference of 1 kv. a large

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd