How does not decrease the magnitude of transfer function

Assignment Help Electrical Engineering
Reference no: EM13259603

If we have a transfer function T(s) = |Z(s)|/|P(s)| and we had a pole at s=-500; Then the magnitude would be sqrt(500^2 + w). So how does that not decrease the magnitude of the transfer function at frequencies below 500?

Reference no: EM13259603

Questions Cloud

Explain the factors which contributed to the rise of race : How in significant ways did Antonio , otherwise known as Anthony Johnson, and John punch help unconsciously to define two different kinds of unequal laws which affected two types of African Americans during the two phases of slavery?
Make an adjusting enrty for the given balance : Make an adjusting enrty for the following. This is unadjusted TB. The book keeper incorrectly credited sales for a recipt onaccount for 4000.This error had not been corrected on Dec 31
Examples of mismatches between teaching and learning styles : Compare the two article how they are similar and how they are different? how do their conclusions compare?
Calculate the average power delivered to the circuit : An AC voltage of the form ?v = 100 sin 1 000t, where ?v is in volts and t is in seconds, is applied to a series RLC circuit. Find the average power delivered to the circuit
How does not decrease the magnitude of transfer function : If we have a transfer function T(s) = |Z(s)|/|P(s)| and we had a pole at s=-500; Then the magnitude would be sqrt(500^2 + w). So how does that not decrease the magnitude of the transfer function at frequencies below 500
Explain how can ethidium ions cause mutations in dna : How can ethidium ions cause mutations in DNA and what type of interactions exists between the DNA and ethidium ions?
Manufacturing overhead rate-overapplied overhead : What is the amount of under- or overapplied overhead at December 31? Prepare the adjusting entry to assign the under- or overapplied overhead for the year to cost of goods sold.
Appropriate assumptions about cost behavior : For this information, make appropriate assumptions about cost behavior and assume that direct labor costs vary directly with thenumber of units produced. How many units must the company sell inorder to earn a pretax profit of $500,000?
Average to break even each week : How many passengers must each of the 70 one-way flights have on average to break even each week?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate location of ei in silicon at liquid nitrogen temp

Calculate the location of Ei in silicon at liquid nitrogen temperature(77k), at room temperature 300k and at 100 degree celsius (let mp =1.0mo and mn= .19m0) Is it reasonable to assume that Ei is the center of the forbidden gap

  What is the maximum negative voltage at the output of cicuit

Due to its wider bandgap than silicon, a GaAs red light emitting diode (LED) typically has a turn-on voltage of 1.6 V. Assuming the maximum allowable current through the LED is 16.7 mA,

  Find when does computer a retransmit the message

The messages being sent are 2 milliseconds long. Computer A starts sending a message on the bus; 250 microseconds later, Computer B starts to send a message, and 250 microseconds after that, Computer C starts to send a message.

  Determine what is the order of the given system

c) Find the output y(t) in response to the input x(t) = 6 u(t), where u(t) is the unit step function. d) Find the output y(t) in response to the input x(t) = δ(t) A linear system has the system response function H(s)= -7/(s+4)

  Find the swr on the line and the reflection coefficient

A lossless transmission line of electrical length l = 0.3? is terminated with a complex load impedance . Find the reflection coefficient at the load, the SWR on the line, the reflection coefficient at the input of the line

  Determine the input impedance zin in the circuit

A power amplifier has a gain of 15db and an input level of 2 volts. Assumming that the input and output impedance are the same. What is the voltage level at the amplifier output.

  Determine the length of the stub length

Using a shorted stub to match load, what is the lenght of the line where the normalized input Y is 1 + jb . If the characteristic impedance of the shorted line is 40 ohms, what is the length of the stub length.

  Develop and implement the counter that counts the sequence

Design the counter using D-flip-flops such that the state codes are the output values of the circuit. For example, when the circuit is in state 011, the output LED's display "off" "on" "on". Thus, no output equations need to be designed.

  Can rectification be obtained with an ohmic contact

Is the high carrier concentration in transparent conductors due to their ideal band structure or to the presence of defects and dopants. If two different materials but with the same work function are brought into contact, does band bending result.

  Implement a circuit that generates vga signals

implement a circuit that generates VGA signals to draw a blue screen on your monitor in a resolution of 640x480. The following materials provide detailed descriptions of how VGA signals operate and some hints on how to design the VGA controller

  How long does it take to discharge the capacitor to 0v

A 1900x10^(-6)F capacitor, intially cahrged to 120V, is discharged by a steady state of 120x10^(-6)A  how long does it take to discharge the capacitor to 0V

  What range of speeds must an induction machine operate

the operation of an induction machine here used as an asynchronous generator her connected to a 3 phase electric system. a) What does asychronous mean in this context b) How is it possible to improve the operation of this generator on the system

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd