How do you classify a structure as determinant

Assignment Help Civil Engineering
Reference no: EM13559342

1.A fine sand has an in-place unit weight of 18.85 kN/m^3 and a water content of 5.2%. The specific gravity of solids is 2.66. Void ratios at densest and loosest conditions are 0.38 and 0.92, respectively. Find the relative density.

2.how do you classify a structure as Determinant, indeterminate (and degree of indeterminacy), or unstable? how do hinges play a part in the degree of indeterminacy?

3.If the design speed of a multilane highway is 60 mph, what is the minimum sight distance that should be provided on the road if (a) the road is horizontal and (b) the road has a maximum grade of 5%? Assume the perception/reaction time is 2.5 seconds. Any help here?

Reference no: EM13559342

Questions Cloud

At what point on the expressway should the motorist : A motorist traveling at 55 mph on an expressway intends to exit from the expressway using an exit ramp with a maximum allowable speed of 30 mph. At what point on the expressway should the motorist step on her brakes in order to reduce her speed to th..
Determine the drivers perception/reaction time before : A test of a driver’s perception/reaction time is being conducted on a special testing track with wet pavement and a driving speed of 55 mph. When the driver is sober, a stop can be made just in time to avoid hitting an object that is first visible 52..
What distance away from the truck was he when he first : A motorist traveling at 55 mph down a grade of 5% on a highway observes an accident involving an overturned truck ahead of him which completely blocked the road
Find when and the distance that a catches up with b : Two objext A and B are moving along the same line. At the time t=0, B is 75ft ahead of A. The acceleration of A is 1.8ft/s^2 and the acceleration of B is -1.3ft/s^2. The velocity of A is 32ft/s and the velocity of B is 51ft/s.
How do you classify a structure as determinant : If the design speed of a multilane highway is 60 mph, what is the minimum sight distance that should be provided on the road if (a) the road is horizontal and (b) the road has a maximum grade of 5%? Assume the perception/reaction time is 2.5 seconds...
An uncovered swimming pool loses 1 inch of water off : An uncovered swimming pool loses 1 inch of water off its 1,000ft^2 surface each week due to evaporation. the heat of vaporization for water at the pool temperature is 1,050 Btu/lb
Calculate the required hourly feed rate of oil in gallons/h : A 50,000 L/day stream of wastewater must be heated from 15 degrees celsius to 40 degrees celsius for a treatment process to work properly. at what rate must we put heat into the stream? assume that wastewater has thermal properties exactly like pure ..
How far must the plug be compressed downward in order to do : The plug has a diameter of 30 mm and fits within a rigid sleeve having an inner diameter of 32 mm. Both the plug and the sleeve are 50 mm long. Determine the axial pressure p that must be applied to the top of the plug to cause
What minimum tracer concentration must be achieved in stream : River A has a flow rate of 3.0 m^3/sec. Stream B discharges into the river at a flow rate of 0.05 m^3/sec. to study mixing of the stream and river, a conservative tracer is to be added to stream B

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the outlet temperature of the engines compressor

The thermal efficiency of an aircraft gas turbine engine (turbojet, based on ideal Brayton cycle) is 25%. The aircraft travels at a speed 770 km/h at an altitude 6800 m above sea level (standard atmospheric air). The combustion chamber outlet temp..

  How far does a horizontal plane depart from a level surface

The width of a lake is 16 km (it is a flat plane tangent to the radius of the sphere). How far does a horizontal plane depart from a level surface if the earth is a sphere with r=6371km

  What thickness of bc will result in same compressive stress

A second load P2 is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the post are dAB= 1.25 in, tAB= 0.5 in, dBC= 2.25 in and tBC= .375 in respectively.

  Is the flow laminar or turbulent and find reynolds number

For Oil (SG=0.86, u=0.025 Ns/m^2) flow of 0.3m^3/s through a round pipe with diameter of 500 mm, determine the Reynolds number. Is the flow laminar or turbulent

  Calculate what is the bod5 of the river water

A BOD5 test sample of river water has the following test data. DO on day 0 = 7.9 mg/L. DO on day 5 = 2.3 mg/L. What is the BOD5 of the river water

  Calculate required area of air to air heat exchange to cool

Calculate the required area of an air to air heat exchange to cool 20,000 cfm from 1200 F to 400 F. Assume ambient air at 80 F will be heated to 800 F by the exchange.

  Calculate the annual water demand on the water supply at the

Assuming an average daily water demand of 400 L/(person. day) during winter months and 700 L/(person. day) during summer months, calculate the annual water demand on the water supply at the end of the design period.

  What maximum load can be applied tot the center of the beam

A simply supported steel 'I beam' is made of three 1"*8" plates with a mass of 898.4 lbmass each as shown in I beam form. Steel has a modulus of elasticity of 30*10^6 psi. The beam is allowed to deflect 1.05 inch.

  How many years will it take to uniformly corrode a thickness

A galvanized (zinc-coated) steel sheet is found to uniformly corrode with an average current density of 1.4 X 10-7 A/cm2. How many years will it take to uniformly corrode a thickness of 0.030 mm of the zinc coating?

  Derive equations for the shear force and the bending moment

(a) Derive equations for the shear force V and the bending moment M for segments: AB, AC and AD (Place the origin at point A). (b) Plot the shear-force and bending-moment diagrams for the beam using the derived functions.

  What are the efforts of work hardening of work materials

What are the effects of hardness, hot strength and hot hardness and work hardening of work materials

  Detremine the cfat in year 0 for the challenger and defender

The defender had a first cost of $300,000, but its market value now is only $100,000. It has chargeable expenses of $120,000 per year and no expected salvage value. To simplify calculations, assume that SL depreciation was charged at $60,000 per y..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd