How are compacted and loose bulk density used in real life

Assignment Help Civil Engineering
Reference no: EM13302412

How are compacted and loose bulk density used in real life. Also is a high degree of accuracy necessary in the bulk density tests?

Reference no: EM13302412

Questions Cloud

Calculate max velocity and subsequent max altitude : A single-stage rocket is launched vertically from rest, and its thrust is programmed to give the rocket a constant upward acceleration of 6 m/s^2 . If the fuel is exhausted 20 s after launch, calculate the maximum velocity and the subsequent maxim..
What is the angular frquency of the cylinder rolling back : A solid cylider of mass 9.8 kg and radius 28 cm is yoked to a spring as shown. What is the angular frquency of the cylinder rolling back
Find the interest paid during the first year : For tax purposes, she needs to know the amount of interest paid during each year of the loan. Find the interest paid during the first year.
What minimum length of cable is needed : The cable below supports a unoformly distributed load. The max tension that the cable can withstand is 41 x 10^6 N, What minimum length of cable is needed
How are compacted and loose bulk density used in real life : How are compacted and loose bulk density used in real life. Also is a high degree of accuracy necessary in the bulk density tests
Determine the average normal strain in rubber : An air-filled rubber ball has a diameter of 6 in. If the air pressure within it is increased until the ball's diameter becomes 7 in., determine the average normal strain in rubber.
Determine its greatest distance from the sun : A comet has a very elliptical orbit with a period of 116.1 y. what is its greatest distance from the Sun
How much error would there be in the volume calculation : Assume the actual water temperature for calibrating a 1/3 ft3 measure was 65 degrees F. If you had used a water temperature of 75 degrees F for your calibration, how much error would there be in your volume calculation (both in ft3 and as a percen..
Ethical implications : Think of a situation that you have experienced or heard about that might be seen as having ethical implications.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the water or cement ratio of the cement paste

Calculate the water/cement ratio of the cement paste in which all the cement will hydrate to leave no capillary pores. (density of cement: 3.1 g/cm3) ?

  Determine the maximum normal strain developed in the board

The man has a mass of 65kg and stands motionless at the end of the diving board. If the board has the cross section, determine the maximum normal strain developed in the board. The modulus of elasticity for the material is E = 117GPa

  How to find degree of kinematic indeterminacy

how to find degree of kinematic indeterminacy

  Determine how long will generator run on a tankful of fuel

A Bonda portable generator is powering a small travelling fridge (120V) in your RV and consumes 125 watts. The efficiency of the generator's gas motor is 23% and the electrical portion (power head) is more efficient at 91%.

  Determine the horizontal reaction

Determine the horizontal reaction that is developed on the gate at C.

  Write a paper on steel sustainability

Write a paper on steel sustainability.

  Critical review decision making of failed major construction

Critical review the decision making of a failed major construction/property project within the UK in the last ten years.

  Determine depth that will result upstream during flood event

A 1.5 m diameter culver (concrete barrel, well - rounded entrance) that is 20m long is installed on a slope of 2 percent. The design discharge is 9.5 m^3/sec and the inlet will be submerged but not the outlet.

  Determine the moment of the force

A force, 90 N in magnitude, is applied to control rod AB as shown. Knowing that the length of the rod is 225 mm, determine the moment of the force about point B by resolving the force into components along AB and in a direction perpendicular to AB..

  Calculate the longitudinal and transverse stresses

Calculate the overall modulus of the composite, explaining your calculations and the assumptions you have made when it is loaded:

  Calculate braking force rb at wheel rim for each system

A bicycle rider would like to compare the effectiveness of candilever hand brakes (use figure a) versus V brakes (figure part b). (a) Calculate the braking force Rb at the wheel rim for each of the bicycle brake systems.

  Standard deviation in lines of levels

Lines of levels were run requiring n instrument setups. If the rod reading for each backsight and foresight has a standard deviation δ what is the standard deviation in each of the following level lines?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd