Hot water at 90c enters a 15-m section of cast iron pipe

Assignment Help Mechanical Engineering
Reference no: EM13345231

Hot water at 90C enters a 15-m section of cast iron pipe, whose inner diameter is 5.3 cm, at an average velocity of 0.65m/s. The outer surface of the pipe is exposed to the cold air at 10C in a basement. If water leaves the basement at 88C, determine the rate of heat loss from the weather.

Reference no: EM13345231

Questions Cloud

Use the wattage of the lightbulb and the time it is on to : use the wattage of the lightbulb and the time it is on to calculate in joules assume that the cylinder and lightbulb
The initial temperature of the calorimeter contents is : a bomb calorimeter whose components have a heat capacity of 6.66 kjdegc is filled with 913 g of water. the amount of
A gas has a volume of 10 l at 0 degrees c what is the final : a gas has a volume of 10 l at 0 degrees c. what is the final temperature of the gas in c if its volume increases to 27
Given the following function in sum-of-product form not : 1. prove using theorems of boolean algebra that bc ba ac abc a. 2. given the following function in sum-of-product
Hot water at 90c enters a 15-m section of cast iron pipe : hot water at 90c enters a 15-m section of cast iron pipe whose inner diameter is 5.3 cm at an average velocity of
Magnesium has three naturally occurring isotopes 24mg : magnesium has three naturally occurring isotopes 24mg isotopic mass 23.9850 amu abundance 78.99 25mg isotopic mass
The mass of the flask is measured when the outside of the : the mass of the flask is measured when the outside of the flask is wet. outside of the flask is dried before the mass
A helium balloon lifts off at 10 atm and 25 degc with a : a helium balloon lifts off at 1.0 atm and 25 degc with a volume of 1.5 x 103 l. at an altitude of 21 km the temperature
Bullet a from west with a mass of 175g and speed of 550ms : bullet a from west with a mass of 175g and speed of 550ms and bullet b from east with a mass of 150g and speed of 200ms

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd