High pressure and low pressure turbines are used

Assignment Help Mechanical Engineering
Reference no: EM13719990

Reheat, where high pressure and low pressure turbines are used, is added to a simple steam cycle to increase the steam quality at the location where the steam exits the low pressure turbine and goes to the condenser. Consider a steam cycle where the turbine entrance pressure and temperature are 3.5 MPa, 400°C, and the condenser pressure is 10 kPa. (a) Compare the turbine exit quality for a simple cycle (without reheat) with that for the low-pressure turbine exit quality of a reheat cycle where the exit at 0.8 MPa of the high-pressure turbine is reheated to 400°C and then expands through the low pressure turbine to 10 kPa. Also, (b) compare cycle efficiencies.

Reference no: EM13719990

Questions Cloud

Determine the total electrical work the heat pump : A Carnot heat pump is to be used for heating house in winter. The house temperature is set at 25oC. One day the outdoor temperature is 2oC. The house is estimated to lose heat at a rate 55000kJ/h (which equal to Qout of the heat pump).
Prepare a succinct statement : Prepare a succinct statement describing Robertson Tool's business risk, making critical judgments - How will the Robertson shareholders react to the results of the analysis
Entropy change from the initial state to the final state : A constant-volume tank contains 10 lbm of ammonia initially at 30 lbf/in^2 and 80(deg)F (539.67(deg)R). The ammonia is then cooled until its pressure drops to 10 lbf/in^2. Determine its entropy change from the initial state to the final state.
Maximizes the decrease in the gibbs free energy of system : An moles of an ideal gas A and (1-n) moles of an ideal gas B, each at 1 atm, are mixed at total constant pressure. What ratio of A to B in the mixture maximizes the decrease in the Gibbs free energy of the system? If decreases in the Gibbs free energ..
High pressure and low pressure turbines are used : Reheat, where high pressure and low pressure turbines are used, is added to a simple steam cycle to increase the steam quality at the location where the steam exits the low pressure turbine and goes to the condenser. Consider a steam cycle where the ..
Demonstrate the law of corresponding states : Demonstrate the law of corresponding states by writing the van der waals equation in terms of the reduced variables. Calculate the compressibility factor for a van der waals gas at its critical point and compare the result with the values obtained fo..
Demonstrate the law of corresponding states : Demonstrate the law of corresponding states by writing the van der waals equation in terms of the reduced variables. Calculate the compressibility factor for a van der waals gas at its critical point and compare the result with the values obtained fo..
Determine the force exerted on bolts due to the water flow : Water flowing through a 10-cm-diameter water pipe at a rate of 0.1 m3/s.  Now a diffuser with an outlet diameter of 20 cm is bolted to the pipe in order to slow down water.  The inlet side of the pipe is part of a continuous piping system (so that th..
Balanced by counterweight equidistant from the fulcrum : The weight of a water tank open to the atmosphere is balanced by a counterweight equidistant from the fulcrum. There is a 4-cm hole at the bottom of the tank, and water level in the tank is maintained constant at 50 cm by water entering the tank hori..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd